Track Roller - Single Flange
`
953 and 963 Track-Type Loader Systems
[M0121021]
953 and 963 Track-Type Loader Systems
Track Roller (Double Flange)
953 and 963 Track-Type Loader Systems
Window Wiper and Wiper Motor
UNDERCARRIAGE
ROLLER GP
D6T Track-Type Tractor Systems
Track Roller - Double Flange
D7E Track-Type Tractor Systems
Track Carrier Roller
D6 Track Type Tractor Machine Systems
Track Roller (Single Flange)
963K Track-Type Loader Machine Systems
Track Roller - Single Flange
963K Track-Type Loader Machine Systems
Track Roller (Double Flange)
953 and 963 Track-Type Loader Systems
Track Carrier Roller
953 and 963 Track-Type Loader Systems
Track Roller (Double Flange)
Show/hide table
| |
| Illustration 1 | g06248531 |
Show/hide table
| |
| Illustration 2 | g06248532 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 4 | 8T-0360 Bolt | Torque to |
| 2 | 2 | 288-0966 Collar | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 3 | 2 | 171-5882 Duo-Cone Seal Gp | The rubber toric seals and all the contacting surfaces must be clean and dry at assembly. Before assembly, apply a thin layer of oil to the contacting surfaces of the metal seal rings. The seal rings must be assembled square. The rubber toric seal should not bulge and the rubber toric seal should not twist. Refer to Special Instruction, SEHS8364, "Assembly and Installation of Conventional Duo-Cone Seals". |
| 4 | 2 | 2H-3928 O-Ring Seal | Before assembly, lubricate the seal. |
| 5 | 2 | 116-6698 Bushing | Before assembly, lubricate the surfaces of the bushing. |
| 6 | 2 | 116-6699 Track Bushing | Bore after assembly is |
| A | - | - | Distance between the bushing and the face of the roller rim on each side is |
| B | - | - | Extension of the track roller shaft from the collar is |
| C | - | - | Installation depth for installing the stopper assembly below the end of the track roller shaft is |
| D | - | - | The clear plug must not be recessed below the surface of the stopper assembly. |
| Install the clear plug so that the end is even with the stopper assembly. The clear plug can extend up to |
|||
| - | - | - | End play for the track roller shaft is: Minimum is Maximum is |
Information System:
953 and 963 Track-Type Loader Systems
Track Roller (Double Flange)
953 and 963 Track-Type Loader Systems
Tilt Cylinder
D7 Track-Type Tractor Electrohydraulic Systems
Speed Sensor - Test
953 and 963 Track-Type Loader Systems
Bank Valve
953 and 963 Track-Type Loader Systems
Piston Motor (Hydrostatic)
Procedure to Install the New Machine Software Group on Certain Telehandlers {7610, 7620}
D7 Track-Type Tractor Electrohydraulic Systems
Solenoid Return - Test
953 and 963 Track-Type Loader Systems
Front Idler and Recoil Spring
C15 and C18 Engines for Caterpillar Built Machines
Engine Oil Pan
DEF Level Gauge Will Not Read Above 3/4 Full on Certain Telehandlers {7451}
D7 Track-Type Tractor Electrohydraulic Systems
Sensor (Data Link Type) - Test
Procedure to Disassemble Broken Track Tensioner on Certain 973D, and 973K Track-Type Loaders {4157, 4158, 4159}
953 and 963 Track-Type Loader Systems
Window Wiper and Wiper Motor
C15 and C18 Engines for Caterpillar Built Machines
Flywheel Housing
Cat Reman Discontinues Complete Reman Engines for Certain Underground Mining Products {1000}
Caterpillar Repainting Process (Chemical Agent Resistant Coating) CARC Paint per MIL-DTL-53072 {0652}
Procedure to Repair or Replace Toggle Switch on Certain Cat</SUP> Products {7332}
Improved Seat Belt Group is Now Used on Certain Wheel Loaders {7327}
C15 and C18 Engines for Caterpillar Built Machines
Fuel Filter Base
C15 and C18 Engines for Caterpillar Built Machines
Housing (Front)
Hood Cracks on Certain TH3510D, TH357D and TH408D Telehandlers {7251}
Left-Hand Side Mirror and Bracket Broken on Certain D Series Telehandlers {7319}
C15 and C18 Engines for Caterpillar Built Machines
Gear Group (Rear)
D7 Track-Type Tractor Electrohydraulic Systems
Ethernet Data Link - Test