Drive Shaft
`
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
[UENR3109]
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Transmission Planetary
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Fixed Axle (Front)
POWER TRAIN
SHAFT GP
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Drive Shaft
Show/hide table
| |
| Illustration 1 | g06106065 |
Show/hide table
| Specification for 372-0613 Drive Shaft Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 20 | 4E-5985 Bolt | Tighten in a crisscross pattern to |
| 2 | - | - | Yokes must be installed in phase as shown. |
| 3 | 1 | 374-4555 Slip Joint | Use 458-0188 Grease to lubricate the spline when the machine is fully articulated. Insert through grease zerk. |
| - | - | - | Before assembly, wipe the face of the bearing cap and the face of the yoke. Make sure that both of the mounting faces are clean. |
Show/hide table
| |
| Illustration 2 | g06106097 |
|
375-8558 Drive Shaft Gp | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 4 | 1 | 197-7996 Setscrew Kit | Use the following procedure in order to install the setscrew: 1. Install the setscrew. 2. Tighten the setscrew until the setscrew bottoms in the keyway. 3. Turn the setscrew outward by one-half turn. 4. Install the lock wire |
| 5 | 4 | 3E-4315 Locking Bolt | Torque to |
| 6 | 1 | 8T-0372 Bolt | Before assembly, apply red Loctite 263 to the threads.
Torque to |
| - | - | - | After shaft is painted, lubricate all the unpainted shaft surfaces with Loctite Graphite-50, prior to bearing assembly. |
Information System:
3516E Generator Set Engine
Aftercooler - Two Stage Aftercooler
C3.4B Engines
Electrical Power Supply - Test
Installation Procedure for Mounting the Rear Radar On Certain Cat</SUP> Products{7347, 7605}
Procedure for Installing Retrofit Radar Holder for Cat</SUP> Object Detection Systems {7347, 7605}
D7E Track-Type Tractor Systems
Electronic Control (HVAC System)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Location of Components (Fan Hydraulic System)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems
Piston Pump (Steering) - Remove and Install
D3K2, D4K2 and D5K2 Track-Type Tractors Systems
Switch Circuits - Test
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Electrohydraulic Control
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems
Hydraulic Tank - Assemble
C3.4B Engines
ECM Memory - Test
Inspect the Alternate Exit on Certain Underground Articulated Trucks and Load Haul Dump Machines{7310}
C4.4 Industrial Engine
Severe Service Application
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems
Main Control Valve - Remove and Install
950M and 962M Wheel Loaders
Hydraulic System Oil Filters - Replace
Guard Rail Installation Procedure for D11T Track-Type Tractors{7150, 7256}
D7E Track-Type Tractor Systems
Location of Components (HVAC System)
631K and 637K Wheel Tractor-Scraper Systems
Calibration Procedures
631K and 637K Wheel Tractor-Scraper Systems
Electronic Control Module (ECM) - Configure
631K and 637K Wheel Tractor-Scraper Systems
Electrical Connector - Inspect
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Fixed Axle (Front)
Procedure to Install a Suction Side Pressure Switch and a Compressor Protection Module to the Air Conditioning Arrangement on Certain D8R Series II Track-Type Tractors{1805, 1808, 7320}
C4.4 Engines for Caterpillar Built Machines
Fuel Injection
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems
Oscillating Axle (Rear)