Exhaust Manifold
`
C13, C15, and C18 Tier 4 Final Engines
[UENR3381]
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines
Engine Oil Pump
AIR INLET AND EXHAUST SYSTEM
MANIFOLD GP-EXHAUST
C13, C15, and C18 Tier 4 Final Engines
Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines
Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines
Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines
Exhaust Manifold
3408E and 3412E Engines for Caterpillar Built Machines
Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines
Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines
Exhaust Manifold
Show/hide table
| |
| Illustration 1 | g02559896 |
Show/hide table
| |
| Illustration 2 | g02559876 |
|
Tightening sequence | |
Show/hide table
| Specification for 343-0588 Exhaust Manifold Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 12 | 9X-6620 Locknut | Before assembly, apply 4C-5599 Anti-Seize Compound to the threads and bearing surfaces.
Torque to Refer to Illustration 2 for the locknut tightening sequence. |
| 2 | 12 | 116-3715 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 3 | 1 | 324-9290 Bellows As | Assemble the bellows assembly with the “Flow Arrow” toward the NOx Reduction System (NRS) cooler.
The total maximum misalignment of the bellows assembly allowed between the NRS cooler and the exhaust manifold elbow is |
| 4 | 2 | 9N-5085 Clamp | Torque to |
| 5 | 1 | 231-9030 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 6 | 6 | 283-2238 Gasket | Install the gasket with tab down as shown in Illustration 1. |
| 7 | 1 | 350-4502 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the inside diameter of the female end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| 8 | 4 | 376-3408 Taperlock Stud | Torque tool speed should not exceed 100 rpm.
Torque to |
| 9 | 1 | 350-4503 Exhaust Manifold | Before assembly, apply thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold.
Remove the excess sealer from the assembled joints. |
| A | - | - | Angle of the V-band clamp is 45 ± 10 degrees. |
Information System:
Reuse and Salvage for C175 Engine Cylinder Blocks {1201}
C13, C15, and C18 Tier 4 Interim Engines
ARD Combustion Supply Air Pressure Is Low
D10T Track-Type Tractor
Mirror - If Equipped
D5R Track-Type Tractor
Winch Cable - Replace
D10T Track-Type Tractor
Mounting and Dismounting
953D, 963D and 973D Track-Type Loaders
Hydraulic System Oil Level Is Low
2009/12/07
An Improved Oil Filler Tube Is Now Used on Certain Medium Wheeloaders and Integrated Tool Carriers {1316}
D9T Track-Type Tractor
Mirror - If Equipped
C13 Tier 4 Final Engines
Aftercooler - Test
2009/08/24
Radiator {1353}
Procedure To Install the New Air Baffle Gp and Cab Insulation{1806}
D6K Track-Type Tractor
Battery Disconnect Switch
C13, C15, and C18 Tier 4 Interim Engines
Speed/Timing - Test
C13, C15, and C18 Tier 4 Interim Engines
Electrical Power Supply - Test
C4.4 Industrial Engine
Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
D11T Track-Type Tractor
Declaration of Conformity
D11T Track-Type Tractor
Power Train Breather - Clean
992K Wheel Loader
Declaration of Conformity
993K Wheel Loader
Declaration of Conformity
854K Wheel Dozer
Declaration of Conformity
D11T Track-Type Tractor
Power Train System Oil Level - Check
D11T Track-Type Tractor
Power Train System Oil Sample - Obtain
844H Wheel Dozer
Declaration of Conformity
D7E Track-Type Tractor Power Train Systems
Steering Does Not Function