Cylinder Head Valves
`
C13, C15, and C18 Tier 4 Final Engines
[UENR3381]
C13, C15, and C18 Tier 4 Final Engines
Fuel Injection Lines
C13, C15, and C18 Tier 4 Final Engines
Exhaust Manifold
BASIC ENGINE
CYLINDER HEAD GP
3408E and 3412E Engines for Caterpillar Built Machines
Cylinder Head Valves
C15 Petroleum Generator Set Engines
Cylinder Head Valves
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
C15 Petroleum Generator Set Engines
Cylinder Head
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
3408E and 3412E Engines for Caterpillar Built Machines
Cylinder Head
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
Show/hide table
| |
| Illustration 1 | g02557404 |
Show/hide table
| Specification for 331-2477 Cylinder Head Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 12 | 252-7802 Inlet Valve | Apply clean engine oil to the stem prior to installation.
Diameter (B) is Face angle (D) is 60.75 ± 0.25 degrees Valve head diameter (F) is |
| 2 | 12 | 248-1467 Exhaust Valve | Apply clean engine oil to the stem prior to installation.
Diameter (C) is Face angle (E) is 45.75 ± 0.25 degrees Valve head diameter (G) is |
| 3 | 24 | 224-4441 Spring | Length under test force is Test force is Approximate free length after test is |
| 4 | 24 | 332-2152 Spring | Length under test force is Test force is Approximate free length after test is |
| 5 | 24 | 268-2953 Valve Guide | Apply clean engine oil to the bore prior to installation.
Bore is Height (A) to the step is |
| 6 | 12 | 260-4855 Valve Seat Insert | Insert angle is 29.75 ± 0.25 degrees
Diameter is Bore in the cylinder head is |
| 7 | 12 | 224-1270 Valve Seat Insert | Insert angle is 44.75 ± 0.25 degrees
Diameter is Bore in the cylinder head is |
Information System:
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System
Piston Pump (Implement) (Pilot)
Procedure To Install New Heat Shields{1067, 1073}
Procedure to Install Improved Brake Oil Cooler Tubes{1380}
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Implement Does Not Raise
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Hydraulic Cylinder Collapse - The Lift Cylinder Will Collapse When The Control Is In The Raised Position
D9T Track-Type Tractor
Battery Disconnect Switch
2011/01/06
Improvements to the Fuel Sender Group {1273, 1408, 6201, 7481, 7857}
953D Track-Type Loader
Declaration of Conformity
TS180, TS185, TS220 and TS225 Towed Scrapers
Declaration of Conformity
953D, 963D and 973D Track-Type Loaders
Hydraulic System Pressure Is High
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems
Implement Cycle Time Is Slow for All Implements
613G Wheel Tractor-Scraper
Maintenance Interval Schedule
2010/12/23
Introduction of Improved Roading Lights for Medium Wheel Loaders {1429}
950H Wheel Loader, 962H Wheel Loader and IT62H Integrated Toolcarrier Electrohydraulic System
Relief Valve (Line)
C15 and C18 Engines for Caterpillar Built Machines
Fuel Transfer Pump
D6T Track-Type Tractor Systems
Piston Pump (Steering) - Test and Adjust
2009/08/24
An Improved Lubrication Pump Is Available for Articulated Trucks and Wheel Loaders {7516, 7540}
2009/09/28
Improved Pivot Shafts Are Now Used {4153}
C4.4 Industrial Engine
Cooling System Coolant Extender (ELC) - Add
C4.4 Industrial Engine
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
938H Wheel Loader and IT38H Integrated Toolcarrier Power Train
Differential Lock Pressure - Check
D11T Track-Type Tractor Machine Systems
Ladder Hinge - Install
D11T Track-Type Tractor Machine Systems
Ladder Hinge - Disassemble
D11T Track-Type Tractor Machine Systems
Ladder Hinge - Assemble