973D Track-Type Loader Power Train Tracks Caterpillar


Tracks
`
973D Track-Type Loader Power Train [KENR6524]
UNDERCARRIAGE
TRACK GP
973D Track-Type Loader Power Train Tracks
973D Track-Type Loader Power Train Tracks



Illustration 1g01949418

Note: All joints of the link assembly must have flexibility even with a measurable end play of zero. Flexibility is the ability for movement from the weight of the link assembly.

Use the following procedure to tighten the track bolts:

  1. Tighten the track bolts to 340 ± 70 N·m (251 ± 52 lb ft).

  1. Tighten the standard track bolts to an additional turn of 120 ± 5 degrees.

  1. Tighten the master link bolts to an additional turn of 180 ± 5 degrees.

The maximum assembly force for the track link assembly ... 310000 N (69691 lb)

(A) Protrusion at one end of the pin ... 4.9 ± 0.8 mm (0.19 ± 0.03 inch)

(C) Distance between the bolt holes ... 146.10 ± 0.39 mm (5.752 ± 0.015 inch)

(D) Distance between the bolt holes ... 204.10 ± 0.39 mm (8.035 ± 0.015 inch)

(E) Distance between the bolt holes ... 146.10 ± 0.80 mm (5.752 ± 0.032 inch)

(F) Distance between the bolt holes ... 204.10 ± 0.80 mm (8.035 ± 0.032 inch)




Illustration 2g01949427

Detail of area B

(G) Distance from the end of the pin (1) to the surface of the stopper (3) ... 8.0 ± 4.0 mm (0.31 ± 0.16 inch)

Note: The plug (2) must not be recessed below the surface of the stopper (3) after assembly.

(H) Distance from the end of the plug (2) to the surface of the stopper (3) ... 0 to 2 mm (0 to 0.1 inch)

End play for the link assemblies ... 0 to 0.20 mm (0 to 0.008 inch)

Information System:

3500 Engines Turbocharger - Install
D7E Track-Type Tractor Power Train Systems Power Train Oil Temperature Is High
2009/09/30 Changes to the Gasket for the Engine Oil Filter Base on Some C11 and C13 Engines {1306, 7555}
3500 Engines Turbocharger - Remove
3500 Engines Fuel Priming Pump - Remove and Install
Procedure to Install an Improved Harness for the Battery Isolation Control{1402, 1408, 1411}
Procedure to Install an Improved Harness for the Battery Isolation Control{1402, 1408, 1411}
D6N Track-Type Tractor Declaration of Conformity
973D Track-Type Loader Power Train Brake System
2009/07/06 New AMOCS Seals That Are Between the Radiator Core and the Tank Are Now in Production on D10T Track-Type Tractors and D11T Track-Type Tractors {1353}
D7E Track-Type Tractor Power Train Systems Brake Does Not Release
A Film Is Missing for the Equalizer Bar End Plug{7206, 7557}
2009/07/06 An Improved Autolube Line is Now Used for 990 Series II and 990H Machines {7510, 7540}
2009/10/29 A Procedure is Now Available In Order to Improve the Lock Assembly on the Rear Guard {7187}
C11, C13, C15, and C18 Industrial Engines Crankcase Pressure Is Low
C9.3 Engines for Caterpillar Built Machines Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Air Control Valve - Remove and Install
Failures of the Axle Oil Cooler in Cold Weather{1365, 3016}
C9.3 Engines for Caterpillar Built Machines Combustion Head - Remove and Install - Clean Emissions Module
973D Track-Type Loader Power Train Electrical Output Components
973D Track-Type Loader Power Train Hydraulic Block
3500 Engines Aftercooler - Remove and Install
D6K Track-Type Tractor Declaration of Conformity
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Piston Motor (Fan Drive)