Fuel Injection Lines
`
C13, C15, and C18 Tier 4 Final Engines
[UENR3381]
C13, C15, and C18 Tier 4 Final Engines
Piston and Rings
C13, C15, and C18 Tier 4 Final Engines
Cylinder Head Valves
FUEL SYSTEM
LINES GP-FUEL INJECTION
C13, C15, and C18 Tier 4 Final Engines
Fuel Injection Lines
Show/hide table
| |
| Illustration 1 | g06473784 |
|
Left side view of engine | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 1 | - | - | Tube assembly to be tightened for single use. Tube is loosened or removed after tightening, tube is to be discarded and replaced. |
| Use the following procedure to tighten the Fuel Lines (6): 1. Install bolts (3) and hand tighten the bolts. 2. Install a new fuel line (6). Hand tighten the fuel line nuts (7) on each end of the fuel line. Repeat for the remaining fuel lines. 3. Install clamps (1), (2), (4), and (5) for the fuel lines and install the nuts. Thread the nuts onto the studs by two full turns. Make sure that the rubber grommets are in place in clamps (1), (2), (4), and (5). 4. Tighten the fuel line nut (7) at the pump and the quill assemblies to a torque of 5. Tighten bolts (3) to standard torque. 6. Tighten the fuel line nut (7) at the fuel rail to a torque of 7. Tighten the nuts for clamps (1), (2), (4), and (5) . |
Information System:
2009/05/18
New Software for the AccuGrade Laser CD610 Display Is Now Available {7220, 7620}
966H Wheel Loader and 972H Wheel Loader Machine Systems
Hood Tilt Actuator
C9 Engines for Caterpillar Built Machines
Flywheel Housing - Remove and Install
C9 Engines for Caterpillar Built Machines
Gear Group (Rear) - Remove and Install
980H Wheel Loader Power Train
Transmission Planetary - Assemble - Heavy Duty
2009/05/11
New Machine Software is Now Used {7620}
AccuGrade</SUP> GPS / Single UTS / Site and Laser Reference v11 for Excavators
Check Sensor Message
C9.3 Tier 4 Final Engines
Diesel Particulate Filter Collects Excessive Soot
C7.1 Industrial Engine
Glossary of Electronic Control Terms
C7.1 Industrial Engine
Electronic Control System
C4.4 Industrial Engine
Cleanliness of Fuel System Components
C7.1 Industrial Engine
Lubrication System
3516B Engine for 994F and 994H Wheel Loaders
Exhaust Has Excessive White Smoke
D5R Track-Type Tractor
Steering Is Unstable
C9.3 Engines for Caterpillar Built Machines
Fuel Filter Base - Remove and Install
3516B Engine for 994F and 994H Wheel Loaders
Oil Consumption Is Excessive
3516B Engine for 994F and 994H Wheel Loaders
Oil Contains Coolant
D5R Track-Type Tractor
Steering Turn Radius Is Large
2009/06/01
Correction to Systems Operation Testing and Adjusting , "Hydraulic Fan System" {1386, 1387, 5050}
2009/05/18
Improved Hardware is Now Available For the Retaining Ring on the Auger Drive for Certain Wheel Tractor-Scrapers {5904}
2009/05/11
New Software for the Engine Electronic Control Module (ECM) is Used {1901, 1902, 1920}
2010/07/02
Introduction of One Piece Piston Cylinder Packs for 3500 High Displacement Engines {1214, 1239, 1331}
C11, C13, C15, and C18 Industrial Engines
Coolant Contains Fuel
C13, C15, and C18 Tier 4 Interim Engines
Diesel Particulate Filter Temperature Is Low