EPC Parts Catalogs

3500 Engines Air Lines Caterpillar


  1. Home
  2. Specifications
  3. #126815
Air Lines
`
3500 Engines [RENR9362]
3500 Engines Air Inlet and Exhaust Lines
3500 Engines Flywheel Housing
AIR INLET AND EXHAUST SYSTEM
LINES GP-AIR
3508B Industrial Engines Air Lines - Air Starting Lines
3508B Industrial Engines Air Lines - Air Starting Lines
3500 Engines Air Lines
3500 Engines Air Lines
3500 Engines Air Lines
3500 Engines Air Lines
3500 Engines Air Lines - Air Starting Lines
Show/hide table
Illustration 1g02550856
Top view

Show/hide table
Table 1
Specification for 286-0638 Air Lines Gp 
Item  Qty  Part  Specification Description 
1  4  197-9732 U-Bolt  Torque to 15 ± 2 N·m (133 ± 18 lb in). 
2  16  216-2211 Clamp  Use the following procedure in order to tighten the clamps:
1. Center the clamps within the marking on the hose.
2. Orient the clamps so that the T-bolts are separated by 90 degrees.
3. Torque to 10 ± 2 N·m (88 ± 18 lb in). 
3  8  6V-3917 O-Ring Seal  Before assembly, Lightly lubricate the bore with 5P-3975 Rubber Lubricant. 
4  4  321-5895 Shield As  During assembly, do not crush the shield assembly. Assemble the shield assembly with the springs and the hooks are at the top of the reducer hose. 
Show/hide table
Illustration 2g02550857
Front view

Show/hide table
Table 2
Specification for 286-0638 Air Lines Gp 
Item  Qty  Part  Specification Description 
5  8  6V-1943 High Temperature Bolt  Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. 
Torque to 55 ± 10 N·m (41 ± 7 lb ft).

Information System:

3500 Engines Air Inlet and Exhaust Lines
3500 Engines Turbocharger
D6T Track-Type Tractor Systems Accumulator (Pilot) - Test and Charge
2009/05/04 A Tilt Regeneration Kit Is Now Available for the 988G and 988H Machines {1408, 5057, 5104, 512R}
D6T Track-Type Tractor Systems Piston Pump (Implement) - Test and Adjust
D6T Track-Type Tractor Hydraulic System Operational Checks
C9.3 Engines for Caterpillar Built Machines Fuel Injection Pump - Test
C13, C15, and C18 Tier 4 Interim Engines Injector Solenoid - Test
C13 Engines for Caterpillar Built Machines Muffler - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
2009/05/04 Improved Installation Procedure for the Heater Cable {7304}
Improved Method for Installing the Actual Gear Position Sensor {1439, 3061}
C4.4 Industrial Engine Air in Fuel - Test
C7.1 Industrial Engine Fuel Injection Timing - Check
C4.4 Industrial Engine Compression - Test
C4.4 Industrial Engine Valve Depth - Inspect
C4.4 Industrial Engine Cooling System Coolant Level - Check
C7.1 Industrial Engine Engine Oil Cooler - Inspect
C7.1 Industrial Engine Connecting Rod - Inspect
C7.1 Industrial Engine Cylinder Head - Inspect
C4.4 Industrial Engine Flywheel - Inspect
C7.1 Engines for Caterpillar Built Machines Vibration Damper - Check
C4.4 Industrial Engine Cooling System - Test
C7.1 Industrial Engine Engine Oil Pump - Inspect