Alternator and Regulator
`
3500B and 3500C Marine Engines
[RENR5077]
ELECTRICAL AND STARTING SYSTEM
ALTERNATOR GP-CHARGING
Show/hide table
![]() | |
Illustration 1 | g03791636 |
Show/hide table
Specification for 333-1184 Charging Alternator Gp | |||
---|---|---|---|
Item | Qty | Part | Specification Description |
- | - | - | Load the battery with a carbon pile 4C-4911 Battery Load Tester in order to get the maximum alternator output. |
1 | 1 | 187-2034 Flange Nut | Torque to |
2 | - | - | Final installation torque is |
3 | 1 | 4B-2047 Nut | Torque to |
4 | - | 6V-8187 Nut | (B-) terminal. Torque to |
5 | - | 6V-8187 Nut | Use a 7/16 ring terminal for (B+) terminal.
(B+) terminal. Torque to |
6 | 1 | 3T-6354 Voltage Regulator As | Voltage setting is not adjustable. |
Permissible voltage range is 27 to 29 V. | |||
- | - | - | Voltage is 24 V. |
- | - | - | Amperage is 60 amp. |
- | - | - | Polarity is negative ground. |
- | - | - | Rotation is either direction. |
- | - | - | Maximum turn on speed is 2000 rpm. |
- | - | - | Alternator performance at Minimum full load current at 5000 rpm is 68 amp. Minimum full load current at 2000 rpm is 42 amp. Output voltage is 28 ± 1 V. |
Information System:
2009/04/27
Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
C11, C13, C15, and C18 Industrial Engines
ECM - Replace
D5R Track-Type Tractor
Hydraulic System Oil Contains Air
C9.3 Engine for Wheel Tractor-Scrapers
Electrical Connectors
D5R Track-Type Tractor
Hydraulic System Has Unusual Noise
C15 and C18 Industrial Engines
Temperature Sensor (DPF) - Remove and Install - Clean Emissions Module
980H Wheel Loader Power Train
Transmission Planetary - Disassemble - Heavy Duty
D5R Track-Type Tractor
MID 039 - CID 2671 - FMI 06
D7E Track-Type Tractor Power Train
Track Adjuster - Assemble
D7E Track-Type Tractor Power Train
Track Adjuster - Disassemble
D7E Track-Type Tractor Power Train
Recoil Cylinder - Assemble
D7E Track-Type Tractor Power Train
Recoil Cylinder - Disassemble
Relocation of the Rear Disconnect Switch {1411}
2009/07/27
A New Fuel Line Is Now Used on D9T Track-Type Tractors {1274}
2009/04/27
Preferred Positions for Mechanically Attached Wear Plates (MAWPS) {6100, 6120, 6820}
Installation of VIMS Guardian on Underground Mining Machines{7601}
C15 and C18 Industrial Engines
Flame Detection Temperature Sensor - Remove and Install - Clean Emissions Module
A New Flange Assembly For the Torque Converter On the D10T Is Now Used{3101}
C13 Tier 4 Final Engines
Lubrication System
2009/05/04
A Repair Kit for the Magnet is Now Available for the AccuGrade CD700 Display {7490}
D5R Track-Type Tractor Hydraulic System
Steering - Calibrate
C9.3 Engines for Caterpillar Built Machines
Electrical Connectors - Inspect
C27 and C32 Engines for Caterpillar Built Machines
Valve Mechanism Cover - Remove and Install - C32
C9.3 Engines for Caterpillar Built Machines
ECM Software - Install