Supplement for the 973C Track-Type Loader with the Steel Mill Arrangement{7000} Caterpillar

Track-Type Loader:

973C (S/N: 3RZ1-UP)

Introduction

This module supplements the following modules for the steel mill arrangement for the 973C track-type loader:

• Hydraulic Schematic, RENR3984

• Systems Operation, RENR3986

• Parts Manual, SEBC1304

Systems Operation

Tow Control Valve in the OPERATE position

Illustration 1	g01005504
(1) Line (2) Line (3) Line (4) Spring (5) Brake release valve (6) Line (7) Electronic control manifold (8) Left brake (9) Right brake (10) Spool (11) Check valve (12) Left drive loop (13) Left drive motor (14) Right drive motor (15) Passage (16) Check valve (17) Line (18) Check valve (19) Hand pump (20) Check valve (21) Dump valve (22) Bypass valve (23) Bypass valve (24) Spool (25) Line (26) Handle (27) Check valve (28) Handle (29) Line (30) Spring (31) Spring (32) Spool (33) Ball valve (34) Check valve (35) Line (36) Line (37) Left drive pump (38) Right drive pump (39) Right drive loop (40) Hydraulic tank (41) Brake release hydraulic tank

When handle (26) of dump valve (21) is in the OPERATE position, ball valve (33) opens a path for the oil through line (35) to hydraulic tank (40). If hand pump (19) is operated, oil flows from brake release hydraulic tank (41) through line (36) to check valve (34). Then, the oil flows from check valve (34) through line (29) to check valve (27) of hand pump (19). The oil flows from hand pump (19) through check valve (18). The oil flows from check valve (18) through line (17) to check valve (16) and to check valve (20). Since the pressure that is required to open check valve (20) is lower than the pressure that is required to open check valve (16), the oil flows through check valve (20) to dump valve (21) and to line (25). Since ball valve (33) is open, the oil pressure in line (25) is insufficient in order to overcome the force of spring (30) and the force of spring (31). With no opposing force against the springs, spring (30) keeps spool (24) shifted upward and spring (31) keeps spool (32) shifted upward.

Oil also flows from check valve (20) through passage (15) to spool (10). Since ball valve (33) is open, the oil pressure in passage (15) is insufficient in order to overcome the force of spring (4) and the force of spring (4) keeps spool (10) shifted downward.

If the parking brake solenoid is energized, brake oil flows from electronic control manifold (7) through line (6) to check valve (11) and the oil seats check valve (11). The oil also flows through line (6) to spool (10). Since spool (10) is shifted downward, oil flows through spool (10) to line (3). The oil flows from line (3) through line (2) to right brake (9). The oil also flows from line (3) through line (1) to left brake (8). The pressure of the oil overcomes the force of the springs of the brakes and the brakes are released.

Tow Control Valve in the TOW position

Illustration 2	g01006289
(1) Line (2) Line (3) Line (4) Spring (5) Brake release valve (6) Line (7) Electronic control manifold (8) Left brake (9) Right brake (10) Spool (11) Check valve (12) Left drive loop (13) Left drive motor (14) Right drive motor (15) Passage (16) Check valve (17) Line (18) Check valve (19) Hand pump (20) Check valve (21) Dump valve (22) Bypass valve (23) Bypass valve (24) Spool (25) Line (26) Handle (27) Check valve (28) Handle (29) Line (30) Spring (31) Spring (32) Spool (33) Ball valve (34) Check valve (35) Line (36) Line (37) Left drive pump (38) Right drive pump (39) Right drive loop (40) Hydraulic tank (41) Brake release hydraulic tank (42) Check valve (43) Check valve (44) Passage (45) Passage (46) Passage (47) Line (48) Line (49) Passage

When handle (26) of dump valve (21) is in the TOW position, ball valve (33) blocks the path for the oil to hydraulic tank (40). When hand pump (19) is operated, oil flows from brake release hydraulic tank (41) through line (36) to check valve (34). Then, the oil flows from check valve (34) through line (29) to check valve (27) of hand pump (19). The oil flows from hand pump (19) through check valve (18). The oil flows from check valve (18) through line (17) to check valve (16) and to check valve (20). Since the pressure that is required to open check valve (20) is less than the pressure that is required to open check valve (16), the oil flows through check valve (20) to dump valve (21) and to line (25). Since ball valve (33) blocks the path for the oil, the pressure in line (25) and the pressure in passage (15) begin to increase.

Oil flows from line (25) to line (48) and to line (47). As hand pump (19) is operated, oil flows through line (47) to spool (24) of bypass valve (22). As the oil pressure in line (47) increases, the oil pressure overcomes the force of spring (30) and spool (24) shifts downward. Oil also flows through line (48) to spool (32) of bypass valve (23). As the oil pressure in line (48) increases, the oil pressure overcomes the force of spring (31) and spool (32) shifts downward.

Oil flows through passage (15) to spool (10). As the oil pressure in passage (15) increases, the oil pressure overcomes the force of spring (4) and spool (10) shifts upward.

When the oil pressure in passage (25) and the oil pressure in passage (15) are sufficient to open check valve (16), oil flows from check valve (16) to passage (49), to passage (45) and to check valve (11). The pressure oil in passage (49) aids the pressure oil in passage (15) in order to keep spool (10) shifted upward. Oil flows through passage (45) to check valve (42). Since the pressure that is required to open check valve (42) is less than the pressure that is required to open check valve (11), oil flows from check valve (42) through passage (46) to line (3). Since check valve (43) prevents any oil flow back to line (6), the oil flows through line (3) to line (1) and the oil flows through line (3) to line (2).

As the pressure in line (1) increases, the pressure overcomes the force of the springs in left brake (8) in order to release the brake and left drive motor (13) is able to rotate. As the pressure in line (2) increases, the pressure overcomes the force of the springs in right brake (9) in order to release the brake and right drive motor (14) is able to rotate. When the bypass valves are shifted downward, the passages of the spools are open and the oil circulates from the drive motors through the bypass valves back to the drive motors in an endless loop.

Parts

191-3495 STEEL MILL AR - European Market

Table 1

MACHINE ARRANGEMENT
191-3495 STEEL MILL AR - European Market
PIN (S/N: 3RZ1-UP)
NOTE			PART NAME							REFERENCE
	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
Y	141-8677	1	GENERAL AR							SEBC1304
Y	165-2785	1	CHASSIS AR							SEBC1304
Y	165-2786	1	POWER TRAIN AR							Table 22
Y	165-2787	1	INSTALLATION AR							SEBC1304
Y	165-2788	1	HYDRAULIC AR							SEBC1304
Y	165-2789	1	UNDERCARRIAGE AR							SEBC1304
Y	214-6089	1	ENGINE AR							Table 2
			*****STANDARD REMOVAL*****
	142-8133	1	ENGINE AR
Y - SEPARATE ILLUSTRATION

·

214-6089 ENGINE AR

Table 2

ENGINE ARRANGEMENT
214-6089 ENGINE AR
PIN (S/N: 3RZ1-UP)
PART OF 191-3495 STEEL MILL AR
			PART NAME
NOTE	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)	REFERENCE
Y	172-6941	1	AFTERCOOLER GP - WATER							SEBC1304
Y	213-2281	1	ALTERNATOR GP - CHARGING							Table 4
YR	8N-5286	1	CYLINDER BLOCK GP							SEBC1304
Y	1P-4244	1	BREATHER GP							SEBC1304
Y	1N-4406	1	CAMSHAFT GP							SEBC1304
Y	4P-8456	1	COOLER GP - FILTER BASE AND ENGINE OIL							SEBC1304
Y	7N-1292	1	COVER GP - CYLINDER BLOCK							Table 5
Y	2P-6528	1	COVER GP - FRONT HOUSING							SEBC1304
Y	4P-9159	1	SUPPRESSION GP - SOUND							Table 6
Y	8N-4745	1	COVER GP - VALVE MECHANISM							SEBC1304
Y	4P-9856	1	CRANKSHAFT GP							SEBC1304
Y	9N-2345	1	DAMPER GP							Table 7
Y	7C-1630	1	FUMES DISPOSAL GP							SEBC1304
Y	152-1682	1	DRIVE GP - FAN							SEBC1304
Y	169-7440	1	FASTENER GP - ENGINE							SEBC1304
Y	120-6629	1	FASTENER GP - OIL PAN							Table 8
Y	8N-5053	1	FASTENER GP - EXHAUST MANIFOLD							SEBC1304
Y	8N-0872	1	FASTENER GP - FRONT HOUSING							SEBC1304
Y	7N-9536	1	FASTENER GP - CYLINDER HEAD							SEBC1304
Y	187-2963	1	FILLER GP - ENGINE OIL							SEBC1304
Y	2W-1011	1	FILTER GP - SECONDARY FUEL							SEBC1304
Y	141-5113	1	FLYWHEEL GP							SEBC1304
Y	115-7542	1	GAUGE GP - OIL LEVEL (DIPSTICK)							SEBC1304
Y	4P-9858	1	GEAR GP - FRONT							SEBC1304
Y	8N-0246	1	CYLINDER HEAD GP							SEBC1304
Y	143-0813	1	HOUSING GP - FLYWHEEL							SEBC1304
Y	8N-0303	1	HOUSING GP - FRONT							SEBC1304
Y	6N-8326	1	LIFTING GR - ENGINE							SEBC1304
Y	194-3235	1	LINES GP - AIR							Table 9
Y	148-3036	1	LINES GP - AIR							SEBC1304
Y	194-4352	1	LINES GP - DRAIN							Table 10
Y	2P-6105	1	LINES GP - ENGINE OIL							SEBC1304
Y	113-5369	1	LINES GP - FUEL INJECTION							SEBC1304
Y	128-4445	1	LINES GP - TURBOCHARGER OIL							SEBC1304
Y	6N-8492	1	LINES GP - AFTERCOOLER WATER							Table 12
Y	4W-6157	1	LINES GP - WATER							SEBC1304
Y	7N-2730	1	MANIFOLD GP - EXHAUST							SEBC1304
Y	7N-8026	1	VALVE MECHANISM GP							SEBC1304
Y	189-6557	1	STARTING MOTOR GP - ELECTRICAL							Table 13
Y	2W-0176	1	MOUNTING GP - ALTERNATOR							SEBC1304
Y	120-6627	1	PAN GP - OIL							Table 14
Y	168-4530	6	PISTON & ROD GP							Table 15
Y	128-7984	1	PROTECTION GP - FUEL SYSTEM							SEBC1304
Y	210-6061	1	PULLEY GP - FAN							Table 16
Y	7N-1142	1	PULLEY GP - CRANKSHAFT							SEBC1304
Y	106-8957	1	PUMP GP - ENGINE OIL							SEBC1304
Y	154-6729	1	PUMP GP - FUEL PRM & PRIM FILTER							SEBC1304
Y	2W-4160	1	PUMP & MTG GP - FUEL TRANSFER							SEBC1304
Y	123-2893	1	PUMP GP - GOV & FUEL INJ							SEBC1304
Y	116-7556	1	PUMP GP - WATER							SEBC1304
Y	8N-0888	1	REGULATOR GP - TEMPERATURE							SEBC1304
Y	2P-6224	1	SEAL GP - CRANKSHAFT							SEBC1304
Y	6I-2108	1	SOLENOID GP - SHUTOFF							SEBC1304
Y	143-3128	1	SUPPORT GP - ENGINE							SEBC1304
Y	141-5102	1	SUPPRESSION GP - SOUND							Table 18
Y	122-4190	1	SUPPRESSION GP - SOUND							Table 19
Y	100-2861	1	SUPPRESSION GP - SOUND							Table 20
Y	8N-0107	1	TRUNION GP - ENGINE							SEBC1304
Y	105-3396	1	TURBOCHARGER GP							SEBC1304
R - REMANUFACTURED PART MAY BE AVAILABLE
Y - SEPARATE ILLUSTATION

Table 3

MEMORANDA

·

213-2281 ALTERNATOR GP - CHARGING

Table 4

ENGINE ARRANGEMENT
213-2281 ALTERNATOR GP - CHARGING
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	3	4W-8320	1	BLOCK
	2	3	9S-1240	1	NUT AS
YR	3	3	185-5294	1	ALTERNATOR GP - CHARGING							Table 21
	4	3	210-4711	1	STRAP AS
		3	6K-8930	1		BOSS
	5	3	219-6466	1	GUARD AS - ALTERNATOR
	6	3	5P-2228	1	BOLT (1/2-13X1 IN)
	7	3	5P-2566	2	BOLT (1/2-13X1.5 IN)
	8	3	6B-6684	2	NUT - FULL (1/2-20 THD)
	9	3	7X-0339	1	BOLT (1/2-13X6.25 IN)
	10	3	8T-4223	3	WASHER - HARD (13.5X25.5X3MM THK)
	11	3	8T-7971	1	WASHER - HARD (13.5X25.5X5MM THK)
	12	3	9L-5134	1	ROD - ALTERNATOR ADJUSTMENT
R - REMANUFACTURED PART MAY BE AVAILABLE
Y - SEPARATE ILLUSTRATION

Illustration 3	g00989636

7N-1292 COVER GP - CYLINDER BLOCK

Table 5

ENGINE ARRANGEMENT
7N-1292 COVER GP - CYLINDER BLOCK
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	4	1M-0130	1	COVER
		4	4M-6480	1	GASKET
	2	4	1A-2029	2	BOLT (3/8-16X1.125 IN)
	3	4	0L-1351	2	BOLT (3/8-16X0.875 IN)
	4	4	8L-8662	1	COVER
		4	5S-8055	1	GASKET
	5	4	4B-3938	1	PLUG - CUP
	6	4	2A-3798	2	DOWEL
	7	4	5M-2894	4	WASHER - HARD (10.2X18.5X2.5MM THK)
	8	4	8M-3267	1	SCREW - HEX SOCKET (3/8-16X0.75 IN)

Illustration 4	g01007415

4P-9159 SUPPRESSION GP - SOUND

Table 6

ENGINE ARRANGEMENT
4P-9159 SUPPRESSION GP - SOUND
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	5	4P-9137	1	COVER AS - SOUND SUPPRESSION
	2	5	4P-9134	1	COVER AS - SOUND SUPPRESSION
	3	5	4P-9133	1	COVER AS - SOUND SUPPRESSION
	4	5	0L-1352	3	BOLT (3/8-16X3.25 IN)
	5	5	5M-2894	10	WASHER - HARD (10.2X18.5X2.5MM THK)
	6	5	0T-0573	2	BOLT (3/8-16X2.75 IN)
	7	5	0L-1143	2	BOLT (3/8-16X2.50 IN)
	8	5	0S-1571	2	BOLT (3/8-16X1.75 IN)
	9	5	9S-8752	2	NUT - FULL (3/8-16 THD)
	10	5	8M-9024	1	WASHER - HARD (10.2X22.5X5MM THK)

Illustration 5	g00989916

·

9N-2345 DAMPER GP

Table 7

ENGINE ARRANGEMENT
9N-2345 DAMPER GP
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	6	1M-0130	1	DAMPER AS
	2	6	4M-6480	1	ADAPTER
	3	6	1A-2029	6	BOLT (1/2-13X1.75 IN)
	4	6	0L-1351	6	WASHER - HARD (13.5X25.5X3MM THK)

Illustration 6	g01007418

120-6629 FASTENER GP - OIL PAN

Table 8

ENGINE ARRANGEMENT
120-6629 FASTENER GP - OIL PAN
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	7	0L-1352	3	BOLT (3/8-16X3.25 IN)
	2	7	1A-2029	10	BOLT (3/8-16X1.125 IN)
	3	7	0S-1591	21	BOLT (3/8-16X1.5 IN)
	4	7	0T-0573	5	BOLT (3/8-16X2.75 IN)
	5	7	2A-4639	7	BOLT (3/8-16X1.625 IN)
	6	7	5M-2894	46	WASHER (2.5MM THK)

Illustration 7	g00989962

194-3235 LINES GP - AIR

Table 9

ENGINE ARRANGEMENT
194-3235 LINES GP - AIR
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	8	113-5346	1	PIPE - AIR
	2	8	5H-7704	2	SEAL - O-RING (94.61MM ID)
	3	8	7W-1945	1	RETAINER
	4	8	5P-4479	1	ELBOW (FLARED - LONG)
	5	8	106-7633	1	TUBE AS - CONTROL
	6	8	7M-8322	1	CLIP
	7	8	3J-7352	1	CONNECTOR
	8	8	3J-7354		SEAL - O-RING (8.92MM ID)
	9	8	2B-2404	1	CLIP
	10	8	2P-0416	1	HOSE
	11	8	3E-7404	2	CLAMP - HOSE
	12	8	0L-1143	1	BOLT (3/8-16X2.50 IN)
	13	8	5M-2894	1	WASHER - HARD (10.2X18.5X2.5MM THK)

Illustration 8	g00989977

194-4352 LINES GP - DRAIN

Table 10

ENGINE ARRANGEMENT
194-4352 LINES GP - DRAIN
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	9	1W-6629	1	TUBE AS - FUEL FILTER
	2	9	4W-7629	1	COVER
YR	3	9	030-7947	1	ELBOW
	4	9	0S-1615	2	BOLT (1/4-20X0.75 IN)
	5	9	3J-1907	1	SEAL - O-RING
	6	9	3J-7352	1	CONNECTOR (7/16-20 STR THD)
	7	9	3J-7354	1	SEAL - O-RING
	8	9	4M-8303	1	SEAL - O-RING
	9	9	5P-0537	2	WASHER - HARD (7.2X14.5X2MM THK)

Illustration 9	g00989984

Table 11

MEMORANDA

·

6N-8492 LINES GP - AFTERCOOLER WATER

Table 12

ENGINE ARRANGEMENT
6N-8492 LINES GP - AFTERCOOLER WATER
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	10	175-3418	1	TUBE AS
	2	10	5M-5860	2	SEAL - O-RING
	3	10	1A-5979	7	BOLT (5/16-18X1.5 IN)
E	4	10	5P-1255		HOSE (11.43CM)
	5	10	0S-1594	2	BOLT (3/8-16X1 IN)
	6	10	175-3419	1	TUBE AS
	7	10	8T-4983	2	CLAMP - HOSE
	8	10	7N-0816	1	TUBE AS - SUPPLY
E	9	10	5P-1257		HOSE (7.62CM)
	10	10	8T-6703	2	PLUG - PIPE
	11	10	6B-7440	1	PLUG - CUP
	12	10	2A-3541	1	GASKET
B	13	10	1A-9579	1	BOLT (5/16-18X1.5 IN)
B	14	10	3E-4352	2	WASHER - HARD (8.8X20.5X2.5MM THK)
	15	10	5M-2894	2	WASHER - HARD (10.2X18.5X2.5MM THK)
B - USE AS REQUIRED
E - ORDER BY THE CENTIMETER

Illustration 10	g00990011

189-6557 STARTING MOTOR GP - ELECTRIC

Table 13

ENGINE ARRANGEMENT
189-6557 STARTING MOTOR GP - ELECTRIC
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	11	4H-7869	1	GASKET
YR	2	11	6V-5227	1	STARTING MOTOR GP - ELECTRIC							SEBC1304
	3	11	8Y-9603	1	CABLE AS - STARTING
E		11	5P-0747			CABLE (00GA) (BLACK) (27.5CM)
	3A	11	1S-7252	1		TERMINAL - RING (FOR 3/8 IN BOLT)
	3B	11	1S-7251	1		TERMINAL - RING (FOR 1/2 IN BOLT)
	4	11	2S-0736	3	WASHER - HARD (17X27X3.5MM THK)
	5	11	8S-2332	3	BOLT - 12 POINT HEAD (5/8-11X1.75 IN)
E - ORDER BY THE CENTIMETER
R - REMANUFACTURED PART MAY BE AVAILABLE
Y - SEPARATE ILLUSTRATION

Illustration 11	g00990055

120-6627 PAN GP - OIL

Table 14

ENGINE ARRANGEMENT
120-6627 PAN GP - OIL
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	12	120-6623	1	COVER
	2	12	4P-5786	1	PLATE AS - OIL PAN
	3	12	169-4199	1	PAN - OIL
	4	12	169-4200	1	GASKET - OIL PAN
B	5	12	7W-6492	1	GASKET
	6	12	9X-6451	2	PLUG - PIPE (1/2-14 NPTF THD)
	7	12	061-9458	2	PLUG - DRAIN
	8	12	7E-4761	1	SEAL - O-RING (28.17MM ID)
	9	12	8L-2786	2	SEAL - O-RING (16.36MM ID)
	10	12	9S-4185	1	PLUG - O-RING (3/4-16 THD)
B	11	12	9S-4190	1	PLUG - O-RING (7/16-20 THD)
B	12	12	2M-9780	1	SEAL - O-RING (19.18MM ID)
B	13	12	7W-6492	1	PLUG - PIPE (1/2-14 NPTF THD)
B - USE AS REQUIRED

Illustration 12	g00990065

168-4530 PISTON & ROD GP

Table 15

ENGINE ARRANGEMENT
168-4530 PISTON & ROD GP
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	13	168-4531	1	BODY AS - PISTON
	2	13	2W-1707	1	RING - PISTON (TOP)
	3	13	2W-1708	2	RING - PISTON (INTERMEDIATE)
	4	13	6I-0497	2	RING - PISTON (OIL)
	5	13	1S-9543	1	RETAINER - PIN
	6	13	7N-9805	1	PIN - PISTON
R	7	13	8N-1721	1	ROD AS - CONNECTING
	7A	13	1P-9956	2		BOLT - CONNECTING ROD
	7B	13	5S-6348	4		NUT
	7C	13	8N-1849	1		BEARING - CONNECTING ROD
	8	13	4W-5739	1	BEARING - CONNECTION ROD (STANDARD)
AB			8N-8221	2	BEARING - CONNECTION ROD (.254MM US)
AB			8N-8222	2	BEARING - CONNECTION ROD (.508MM US)
AB			8N-8223	1	BEARING - CONNECTION ROD (.762MM US)
A - NOT PART OF THIS GROUP
B - USE AS REQUIRED
R - REMANUFACTURED PART MAY BE AVAILABLE

Illustration 13	g00990079

·

210-6061 PULLEY GP - FAN

Table 16

ENGINE ARRANGEMENT
210-6061 PULLEY GP - FAN
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	14	209-6575	1	ADAPTER - FAN
	2	14	1N-4654	1	PULLEY - FAN DRIVE
	3	14	9F-4446	1	SEAL - O-RING
	4	14	1W-4369	1	PULLEY - ALTERNATOR
	5	14	8T-9101	6	BOLT (3/8-16X2.75 IN)
	6	14	6V-8801	6	NUT (3/8-16 THD)
	7	14	7N-9417	1	V-BELT SET (INCLUDES 2 BELTS)
	8	14	1P-9744	1	V-BELT
	9	14	3S-2093	1	STRAP - CABLE

Illustration 14	g00990087

Table 17

MEMORANDA

·

141-5102 SUPPRESSION GP - SOUND

Table 18

ENGINE ARRANGEMENT
141-5102 SUPPRESSION GP - SOUND
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	15	4P-9881	1	PANEL AS - RH
	2	15	4B-3388	16	BOLT (5/16-18X1.125 IN
	3	15	9N-0869	17	WASHER - HARD (8.8X25.5X2MM THK)
	4	15	0S-1566	2	BOLT (5/8-11X1.5 IN)
	5	15	5P-8247	2	WASHER - HARD (17X32X3.5MM THK)
	6	15	141-5101	1	PANEL AS - LH
	7	15	002-1626	1	BOLT (5/16-18X1 IN)
B	8	15	4B-3388	1	BOLT (5/16-18X1.125 IN)
B	9	15	6N-0869	1	WASHER - HARD (8.8X25.5X2MM THK)
B - USE AS REQUIRED

Illustration 15	g00990101

·

122-4190 SUPPRESSION GP - SOUND

Table 19

ENGINE ARRANGEMENT
122-4190 SUPPRESSION GP - SOUND
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	16	120-6628	1	COVER AS - SOUND SUPPRESSION
	2	16	0S-1588	2	BOLT (3/8-16X1.25 IN)
	3	16	5M-2894	2	WASHER - HARD (10.2X18.5X2.5MM THK)
	4	16	1B-2790	8	BOLT (5/16-18X1.375 IN)
	5	16	3E-4352	8	WASHER - HARD (8.8X20.5X2.5MM THK)
	6	16	8M-9124	1	WASHER (10X22.5X8MM THK)

Illustration 16	g00990115

100-2861 SUPPRESSION GP - SOUND

Table 20

ENGINE ARRANGEMENT
100-2861 SUPPRESSION GP - SOUND
(S/N: 13Z45526-UP)
PART OF 214-6089 ENGINE AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	17	6I-1656	1	PANEL - VALVE COVER
	2	17	6I-2867	1	SHIELD - HEAT
	3	17	0S-1618	3	BOLT (5/16-18X1 IN)
	4	17	8B-8679	3	SPACER (.44X.406X.75 IN THK)
	5	17	9M-1974	3	WASHER - HARD (8.8X16X2MM THK)
	6	17	128-0067	5	CLIP

Illustration 17	g00990124

185-5294 ALTERNATOR GP - CHARGING

Table 21

ENGINE ARRANGEMENT
185-5294 ALTERNATOR GP - CHARGING
(S/N: 13Z45526-UP)
PART OF 213-2281 ALTERNATOR GP - CHARGING
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	18	185-2653	1	FRAME
	2	18	5S-7349	1	BOLT (1/4-20X0.5 IN)
	3	18	185-2639	1	FAN AS
	4	18	1H-3244	1	LOCKWASHER
	5	18	185-2645	1	FRAME
	6	18	2K-4821	1	LOCKNUT (5/8-18 THD)
	7	18	5P-8247	1	WASHER - HARD (17X33X3.5MM THK)
	8	18	185-2651	1	COVER
	9	18	8T-4205	1	WASHER - HARD (7.2X14.5X2MM THK)
	10	18	185-2647	1	GROMMET
	11	18	9L-6770	1	CAP
	12	18	185-2642	1	STATOR AS
	13	18	185-2638	2	COLLAR
	14	18	185-2654	1	PLATE
	15	18	185-2650	1	ROTOR AS
	16	18	185-2644	1	COIL AS
	17	18	185-2648	1	REGULATOR AS
	18	18	6V-8189	1	NUT (5/16-18 THD)
	19	18	8T-4224	1	WASHER - HARD (8.8X16X2MM THK)
	20	18	3F-9556	1	LOCKWASHER
					AVAILABLE REPAIR KITS:
			185-2655		KIT - BEARING (ALTERNATOR) (INCLUDES 2 BEARINGS)
			185-2656		KIT - TERMINAL (ALTERNATOR) (INCLUDES HOLDER AS, PLATE, INSULATOR, PIN, BOLT, GROMMET & NUT)
			185-2657		KIT - TERMINAL (ALTERNATOR) (INCLUDES INSULATORS, WASHERS & NUTS)
			185-2658		KIT - HARDWARE (ALTERNATOR) (INCLUDES BOLTS)

Illustration 18	g00990182

165-2786 POWER TRAIN AR

Table 22

POWER TRAIN
165-2786 POWER TRAIN AR
PIN (S/N: 3RZ1-UP)
PART OF 191-3495 STEEL MILL AR
NOTE			PART NAME							REFERENCE
	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
Y	141-8680	1	POWER TRAIN AR							SEBP3011
Y	167-3807	1	LINES GP - HYDROSTATIC							Table 24
Y	169-1669	1	DRIVE GP - FLEXIBLE COUPLING							SEBC1304
Y	169-1681	1	FINAL DRIVE & BRAKE GP							SEBC1304
Y	175-1816	1	LINES GP - BRAKE							Table 25
Y	196-5733	1	TANK GP - HYDRAULIC							SEBC1304
			*****STANDARD REMOVAL*****
	151-1233	1	LINES GP - HYDROSTATIC
	151-1237	1	LINES GP - BRAKE
	154-7323	1	TANK GP - HYDRAULIC
Y - SEPARATE ILLUSTRATION

Table 23

MEMORANDA

·

167-3807 LINES GP - HYDROSTATIC

Table 24

POWER TRAIN
167-3807 LINES GP - HYDROSTATIC
PART OF 165-2786 POWER TRAIN AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	19	3E-4356	16	WASHER - HARD (6MM THK)
	2	19	5P-4868	8	CLAMP (HOSE)
	3	19	039-8557	16	WASHER (6MM THK)
	4	19	174-3553	2	HOSE AS
	5	19	174-3554	2	HOSE AS
	6	19	211-8158	2	VALVE GP - BYPASS
	7	19	1P-5767	8	FLANGE - HALF
	8	19	5P-8077	8	FLANGE - HALF
	9	19	6V-3335	4	SEAL - RECTANGULAR
	10	19	6V-3336	4	SEAL - RECTANGULAR
M	11	19	8T-4140	16	BOLT (M16X2.0X60MM)
M	12	19	8T-4176	16	BOLT (M12X1.75X90MM)
BE	13	19	167-3827		INSULATION
B - USE AS REQUIRED
E - ORDER BY THE CENTIMETER
M - METRIC PART

Illustration 19	g00990518

·

175-1816 LINES GP - BRAKE

Table 25

POWER TRAIN
175-1816 LINES GP - BRAKE
PART OF 165-2786 POWER TRAIN AR
NOTE					PART NAME							REFERENCE
	REFERENCE NUMBER	ILLUSTRATION NUMBER	PART NUMBER	QTY	1	2	3	4	5	6	(Product Level)
	1	21	5P-3903	1	ADAPTER - O-RING
M	2	20	8T-4196	1	BOLT (M10X1.5X35MM
M	3	21	8T-4191	4	BOLT (M10X1.5X15MM)
M	4	20	8T-4186	5	BOLT (M10X1.5X40MM
M	5	20	8T-4178	1	BOLT (M10X1.5X0MM)
M	6	20	8T-4172	1	BOLT (M10X1.5X80MM)
M	7	20, 22	8T-4137	8	BOLT (M10X1.5X20MM)
M	8	20	8T-4136	1	BOLT (M10X1.5X25MM)
M	9	20	5P-8347	2	BOLT (M8X1.25X70MM))
	10	20	5M-3062	2	BOLT (3/8-16X.75 IN)
M	11	20	8T-4908	1	BOLT (M8X1.25X25MM)
	12	20	3W-9481	4	BOSS
	13	20	8S-0948	1	CLIP
	14	20	8M-2773	1	CLIP
	15	20	8M-2770	6	CLIP
	16	20	6D-4247	3	CLIP
	17	20	5P-9297	2	CLIP
	18	20	4D-7735	1	CLIP
	19	20	1S-1015	1	CLIP
	20	20, 22	4B-0418	10	CLIP
	21	20	164-5612	1	CONNECTOR
	22	20	148-8340	1	CONNECTOR
	23	20	148-8318	1	CONNECTOR
	24	21	148-8378	1	ELBOW
	25	21,22	148-8370	2	ELBOW
	26	20, 21	148-8364	3	ELBOW
	27	20	148-8354	1	ELBOW
	28	20	8T-0252	1	ELBOW
	29	20	172-4042	1	HANDLE
I	30	20	177-2032	1	HOSE AS
I	31	20	175-1830	1	HOSE AS
I	32	20	175-1826	1	HOSE AS
I	33	21	175-1822	1	HOSE AS
I	34	20	175-1819	1	HOSE AS
I	35	21	162-3967	1	HOSE AS
I	36	20	226-6421	1	HOSE AS
I	37	20	196-2636	1	HOSE AS
I	38	20	196-2635	1	HOSE AS
I	39	20	191-2707	1	HOSE AS
I	40	20	189-3564	1	HOSE AS
I	41	21	189-2044	1	HOSE AS
I	42	21	189-2043	1	HOSE AS
M	43	20, 22	8T-4133	4	NUT (M10X1.5 THD)
M	44	20	5C-7261	2	NUT (M8X1.25 THD)
	45	21	6V-8556	1	NUT (1 3/16-12 THD)
	46	20	229-8985	1	PLATE
	47	20	175-1815	1	PLATE
	48	20	175-9085	1	PUMP GP - HAND
	49	21	148-8417	1	REDUCER AS
	50	20	148-8415	1	REDUCER AS
	51	20	5M-6755	4	SCREW - MACHINE
	52	20, 21, 22	6V-8398	12	SEAL - O-RING (12.47MM ID)
	53	20,21	6V-8397	2	SEAL - O-RING (9.27MM ID)
	54	21	6K-6307	1	SEAL - O-RING (43.69MM ID)
	55	20	3K-0360	1	SEAL - O-RING (16.36MM ID)
	56	20	197-2433	2	SPACER (50MM THK)
	57	20	1K-4649	1	SPACER (1.0IN THK)
	58	20	224-9200	1	TANK AS
	59	21	148-8449	1	TEE GP - SWIVEL
	60	21	148-8444	2	TEE GP
	61	21	148-8439	1	TEE AS
	62	21	148-8434	1	TEE AS
	63	20	148-8428	1	TEE GP
	64	20	148-8426	1	TEE GP
	65	22	195-9845	1	TUBE AS
	66	20	195-9844	1	TUBE AS
	67	20	195-9818	1	TUBE AS
	68	20	195-7851	1	TUBE AS
	69	20	195-7850	1	TUBE AS
	70	20	175-1820	1	TUBE AS
	71	21	162-3866	1	TUBE AS
	72	22	162-3008	1	TUBE AS
	73	20	164-5570	2	UNION GP
	74	20	187-7658	1	VALVE AS
	75	20	6E-5444	1	VALVE GP - CHECK
	76	20	231-5161	1	VALVE GP - CONTROL
	77	20	9X-8267	4	WASHER (6.6X12.2MM THK)
	78	20	8T-4896	2	WASHER - HARD (10.2X18X2.5MM THK)
	79	20	8T-4224	5	WASHER - HARD (8.8X16X2MM THK)
	80	20, 21, 22	8T-4121	24	WASHER - HARD (11X21X2.5MM THK)
I - SEE HOSE FABRIAVSION GUIDE
M - METRIC PART

Illustration 20	g01003741

Illustration 21	g01003742

Illustration 22	g01004718