Guard Rail Installation Procedure for D11T Track-Type Tractors{7150, 7256} Caterpillar


`
Guard Rail Installation Procedure for D11T Track-Type Tractors{7150, 7256} [REHS5367]
FRAME AND BODY
HANDRAIL GP
1.1. Introduction
2.1. Safety
3.1. Standard Guard Rail Installation Procedure
4.2. Required Parts
5.2. Left-Hand Side Guardrail Installation
6.2. Right-Hand Side Guardrail Installation
7.2. Hydraulic Tank Guardrail Installation
Track-Type Tractor:
D11T (S/N: AMA1-UP; MDG1-UP; JEL1-UP; JNS1-UP)

Introduction

This special instruction provides the installation procedure for the standard guard rails on D11T Track-Type Tractors.

Do not perform any procedure that is outlined in this publication until you have read the information and you understand the information. Do not order any parts until you have read the information and you understand the information.

Safety

------ WARNING! ------

Do not attempt to disassemble or assemble this machine until you read and understand the disassembly and assembly instructions. Improper disassembly and assembly procedures could result in injury or death.

----------------------

Standard Guard Rail Installation Procedure

Required Parts

Table 1
Required Parts    
Item     Qty     Part Number     Part Description    
1     1     3T-2977     Plate    
2     8     8C-8585     Screw    
3     2     362-2899     Support As    
4     4     8T-4195     Bolt    
5     4     8T-4121     Hard Washer    
6     1     343-9932     Guardrail As    
7     35     8T-4139     Bolt    
8     22     7X-0584     Hard Washer    
9     1     346-3281     Guard    
10     16     8T-4192     Bolt    
11     18     5P-1076     Hard Washer    
12     15     8T-4223     Hard Washer    
13     1     343-9916     Guardrail As    
14     1     343-9917     Guard    
15     1     465-0423     Guardrail As    
16     6     5P-7469     Clip    
17     6     5P-7468     Clip    
18     6     6V-1874     Grommet    
19     1     115-3580     Plate    
20     2     8T-4183     Bolt    
21     2     329-3356     Nut    

Left-Hand Side Guardrail Installation




    Illustration 1g02691680

    Overall view of left side machine guardrail




    Illustration 2g02691716

  1. Attach plate (1) to fender with four screws (2) .



    Illustration 3g02692018

  1. Attach two support assemblies (3) to fender assembly with four bolts (4) and four washers (5) .



    Illustration 4g02693198

  1. Attach guardrail assembly (6) to fender assembly and support assembly (3) with 12 bolts (7) and 12 washers (8) .

    Note: Two bolts (7) and two washers (8) should be used at each post.




    Illustration 5g02693317

  1. Attach guard (9) to guardrail assembly (6) with eight bolts (10) and eight washers (11) .



    Illustration 6g02693741

  1. If the holes are not already plugged, install four screws (2) into the fender assembly.



    Illustration 7g02693836

  1. If the holes are not already plugged, install 11 bolts (7), nine washers (12), and two washers (8) .

Right-Hand Side Guardrail Installation




    Illustration 8g02717934

    Overall view of right side machine guardrails




    Illustration 9g02694081

  1. Attach guardrail assembly (13) to fender assembly with eight bolts (7) and eight washers (8) .



    Illustration 10g02694316

  1. Attach guard (14) to guardrail assembly (13) with eight bolts (10) and eight washers (11) .

Hydraulic Tank Guardrail Installation




    Illustration 11g03723052

    Overall view of the hydraulic tank guardrail




    Illustration 12g03723061

  1. Attach guardrail assembly (15) to the hydraulic tank with four clips (16), four grommets (18), four clips (17), four bolts (7) and four washers (12) .



    Illustration 13g03723107

  1. Attach guardrail assembly (15) to guardrail assembly (13) with two bolts (20), two washers (11), plate (19), two clips (16), two grommets (18), two clips (17), two washers (12), and two nuts (21) .

Information System:

950M and 962M Wheel Loaders Hydraulic System Oil Filters - Replace
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Main Control Valve - Remove and Install
C4.4 Industrial Engine Severe Service Application
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Drive Shaft
3516E Generator Set Engine Aftercooler - Two Stage Aftercooler
C3.4B Engines Electrical Power Supply - Test
Installation Procedure for Mounting the Rear Radar On Certain Cat Products{7347, 7605}
Procedure for Installing Retrofit Radar Holder for Cat Object Detection Systems {7347, 7605}
D7E Track-Type Tractor Systems Electronic Control (HVAC System)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Location of Components (Fan Hydraulic System)
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Piston Pump (Steering) - Remove and Install
D3K2, D4K2 and D5K2 Track-Type Tractors Systems Switch Circuits - Test
D7E Track-Type Tractor Systems Location of Components (HVAC System)
631K and 637K Wheel Tractor-Scraper Systems Calibration Procedures
631K and 637K Wheel Tractor-Scraper Systems Electronic Control Module (ECM) - Configure
631K and 637K Wheel Tractor-Scraper Systems Electrical Connector - Inspect
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Fixed Axle (Front)
Procedure to Install a Suction Side Pressure Switch and a Compressor Protection Module to the Air Conditioning Arrangement on Certain D8R Series II Track-Type Tractors{1805, 1808, 7320}
C4.4 Engines for Caterpillar Built Machines Fuel Injection
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Oscillating Axle (Rear)
C3.4B Engines Glow Plug Starting Aid - Test
966M and 972M Wheel Loaders Cooling System Coolant Extender (ELC) - Add
2014/09/16 New Inspection and Repair Procedure Is Now Available for Cat Products Located in India Equipped with Product Link {7606}
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Calibrations (Cat ET)