Installation Procedure for the 454-2355 Lines Gp - Coupler on Certain Wheel Loaders {5057, 6129} Caterpillar

Installation Procedure for the 454-2355 Lines Gp - Coupler on Certain Wheel Loaders {5057, 6129} [GEHS0743]

HYDRAULIC SYSTEM

LINES GP-COUPLER

Installation Procedure for the 454-2355 Lines Gp - Coupler on Certain Wheel Loaders {5057, 6129}

1.1. Introduction

2.1. Safety Section

3.1. Welding Requirements

4.1. Required Parts

5.1. Installation Procedure

6.2. Mounting Brackets

7.2. Hydraulic Components

8.2. Electrical

9.1. Software Configuration

Wheel Loader
966M (S/N: MD71-UP; EJA1-UP; DYC1-UP; R8D1-UP; LMM1-UP; KJP1-UP; L8R1-UP; GMS1-UP)
966M Series XE (S/N: FL21-UP; P6C1-UP; DZL1-UP; B8P1-UP; XCR1-UP)
972M (S/N: A781-UP; L8E1-UP; LSJ1-UP; GGN1-UP; WGN1-UP; A8P1-UP; JPR1-UP; M8W1-UP)
972M Series XE (S/N: AN31-UP; L9S1-UP; M5S1-UP; EDW1-UP; R1Z1-UP)
Work Tool
QUICK COUPLER (S/N: Y7A1-UP; Y8B1-UP; A8K1-UP)

Revision History:

Show/hide table

Table 1
Revision	Summary of Changes
04	Added Software Configuration Section.

Introduction

This special instruction covers the installation procedure for 454-2355 Lines Gp - Coupler.

The coupler lines group consists of a switch in the cab, and a control valve and pressure lines which supply hydraulic pressure to the quick coupler. The switch has two positions that are used for coupling and uncoupling the work tool. Pressure for the operation of the quick coupler is supplied by the implement pump.

Safety Section

Show/hide table

NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat^® products. Dispose of all fluids according to local regulations and mandates.

Show/hide table

Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.

Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.

Show/hide table

Personal injury or death can result from improperly checking for a leak.
Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.

If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.

Show/hide table




Illustration 1	g00104545

Prevent the machine from movement. Park the machine on a level surface.

Attach a "Do Not Operate" warning tag or a similar warning tag to the start switch or to the controls before you service the equipment . These warning tags (Special Instruction, SEHS7332) are available from your AVSpare dealer.

Welding Requirements

Show/hide table

Personal injury or death can result from fumes, gases and ultraviolet rays from the weld arc.
Welding can cause fumes, burn skin and produce ultraviolet rays.
Keep your head out of the fumes. Use ventilation, exhaust at the arc, or both, to keep fumes and gases from your breathing area. Wear eye, ear and body protection before working.
Protect yourself and others; read and understand this warning. Fumes and gases can be dangerous to your health. Ultraviolet rays from the weld arc can injure eyes and burn skin. Electric shock can cause death.
Read and understand the manufacturer's instructions and your employer's safety practices. Do not touch live electrical parts.
See "American National Standard Z49.1, Safety in Welding and Cutting" published by the American Welding Society.
American Welding Society
2501 N.W. 7th Street
Miami, Florida 33125

See "OSHA Safety and Health Standards, 29 CFR 1910", available from U.S. Department of Labor.
U.S. Department of Labor
Washington, D.C. 20210

Welding quality is critical to the success of the installation procedures. Welds must be smooth and continuous. Do not undercut the welds. No overlap is allowed. Grind the ends of the welds to a smooth radius.

All electrodes must be dried completely. The electrodes can be dried by heating the electrodes to 300°C (572°F). The electrodes must be dried for at least 30 minutes.

Do not weld in windy conditions. Do not weld when temperatures are below 16°C (60°F).

Penetration characteristics may vary greatly depending on the following conditions:

Electrode diameter
Shielding gas
Welding current
Plate thickness

The following items also affect the welds:

Geometry of welded joints
Surface conditions
Composition of the base metal and of the electrode

A root pass should be applied before each weld is finished.

Maintain a 3 mm (0.12 inch) minimum root opening on all cross welds and circle welds.

All welds to the stick must be welded in the direction from the rear of the stick toward the front of the stick.

For more welding information, consult the AVSpare Service Welding Guide, SEBD0512.

Required Parts

Show/hide table

Table 2
454-2355 Lines Gp - Coupler (- 04)
Item	Qty	Part No	Description
(1)	2	6V-9829	Cap As
(2)	2	112-1817	Ball Valve
(3)	1	8Y-3795	Boss
(4)	1	123-4750	Check Valve As
(5)	6	148-8336	Connector As
(6)	1	148-8351	Elbow As
(7)	2	148-8353	Elbow As
(8)	2	148-8367	Elbow As
(9)	1	148-8378	Elbow As
(10)	1	160-8708	Bracket As
(11)	1	162-8264	Tee As
(12)	1	324-3471	Bracket
(13)	1	367-0350	Tube As
(14)	1	367-0351	Tube As
(15)	2	383-4355	Hose As
(16)	1	416-4796	Control Valve and Mounting Gp
(17)	1	418-3768	Bracket As
(18)	1	418-3771	Tube As
(19)	1	472-0175	Tube As
(20)	1	423-9937	Hose As
(21)	1	423-9938	Hose As
(22)	1	423-9939	Hose As
(23)	1	427-4963	Quick Coupler Switch Gp
(23a)	1	424-4914	Rocker Switch
(24)	8	096-6166	Hard Washer
(25)	8	121-4405	Bolt
(26)	1	150-4043	Connector As
(27)	14	5P-9297	Clip
(28)	1	6D-3479	Clip
(29)	4	6V-8397	O-Ring Seal
(30)	17	8T-4121	Hard Washer
(31)	2	8T-4133	Nut
(32)	8	8T-4136	Bolt
(33)	5	8T-4137	Bolt
(34)	2	8T-4172	Bolt
(35)	2	8T-4192	Bolt
(36)	2	8T-4223	Hard Washer
(37)	1	8X-7415	Plate
(38)	1	9R-2613	Weld Boss
(39)	2	9R-2821	Boss
(40)	1	5P-7462	Clip
(41)	1	5P-7463	Clip
(42)	1	6V-0683	Grommet

Show/hide table




Illustration 2	g03777361
454-2355 Coupler Lines Gp