TH220B, TH330B and TH340B Telehandlers Lifting Capacities Caterpillar


Lifting Capacities
`
1.1. Examples of Estimating the Lift Operation from the Load Chart
2.2. Example 1
3.2. Example 2
4.2. Example 3

------ WARNING! ------

The instability of the machine can result in injury or death. In order to ensure the stability during operation, the following conditions must be observed.

The tires must be inflated correctly and the tires must have the correct amount of ballast (if equipped).

The machine must be level.

The correct load chart must be referenced for the work tool that is installed on the machine. The specified weights and load centers must never be exceeded.

The machine must never be moved when the boom is raised above the travelling position.


On the 340B, the boom angle reference scale and the boom extension reference scale are standard equipment.

In certain markets, the boom angle reference scale and the boom extension reference scale will be offered as an option for the 220B and the 330B. Your AVSpare dealer will be able to equip your machine with the boom angle reference scale and the boom extension reference scale.

On machines that are not equipped with the boom angle reference scale and the boom extension reference scale, it may be difficult to accurately position a load within the areas that are shown on the load charts.

While the machine is active,AVSpare strongly recommends the use of the boom angle reference scale and the boom extension reference scale when operators refer to load charts. The use of load charts is the only recommended method of reducing the risk that is associated with longitudinal stability. Even if an LSI system is installed, the same level of longitudinal stability will not be achieved as the level of stability that is obtained with the accurate use of load charts. Refer to the “Longitudinal Stability Indicator” section of Operation and Maintenance Manual, "Monitoring System" for more information on the LSI system.



Illustration 1g00955167

The load charts are located on the dash panel at the right side of the instrument cluster. Ensure that the correct load chart is used. The chart is intended for the type of attachment that is represented by a symbol at the top of the chart. The load charts may be in metric units (meters and kilograms) or conventional units (feet and pounds).

When the machine is operated on tires, the weight of the intended load determines the maximum height above ground. The weight of the intended load also determines the maximum distance that is between the load center of gravity and the front wheels.

The machine boom has two scales which must be used for reference with the load chart in order to assess the lift operation. The boom extension reference scale gives an indication of the boom length. For the 220B and 330B machines, the letters "B" and "C" correspond to the same letters on the load chart. The letter "A" on the load chart corresponds to the fully retracted position of the boom. The letter "D" on the load chart corresponds to the fully extended position of the boom. For the 340B machines, the letters "B", "C" and "D" correspond to the same letters on the load chart. The letter "A" on the load chart corresponds to the fully retracted position of the boom. The letter "E" on the load chart corresponds to the fully extended position of the boom.



Illustration 2g00955168

Boom angle reference scale (1) gives an indication of the angle of the boom.

Follow the instructions below in order to assess the intended load:

  1. Carefully position the machine. The machine should be as close as possible to the intended load. For more information on operating the machine, refer to the appropriate topic in the Operation Section of the Operation and Maintenance Manual.

  2. In order to move the attachment into position for the operation, raise the boom and extend the boom, as required. Do not make the lift operation.

  3. Look at the boom extension reference scale and the boom angle reference scale and note the readings. Refer to the load chart and use these two values in order to locate the equivalent load zone.

  4. If the intended load is equal to the value in the equivalent load zone the lift operation can be attempted with caution. Also, if the intended load is less than the value in the equivalent load zone the lift operation can be attempted with caution.

  5. If the intended load is heavier than the value in the equivalent load zone the lift operation cannot be made.

Examples of Estimating the Lift Operation from the Load Chart

Note: In the examples that follow, the numbers are from the load chart that is shown at the end of this section. This load chart is only for illustrative purposes. This load chart does not relate to any particular machine. The numbers that are quoted have no units. The units on the load charts which are installed in a particular machine may be kilograms or pounds.

Example 1

  • The weight of the intended load is 45 units.

  • The boom angle reference is 56 degrees.

  • The boom extension reference scale is at "D".

With reference to the load chart, "X" is the point of intersection for the values of the boom angle reference and the boom extension reference. This point of intersection is in the load zone for 80 units. The intended load of 45 units is less than the value in the load zone so the load chart indicates that the load is within the capacity of the machine.

Example 2

  • The weight of the intended load is 125 units.

  • The boom angle reference is 40 degrees.

  • The boom extension reference scale is at "B".

With reference to the load chart, "Y" is the point of intersection for the values of the boom angle reference and the boom extension reference. This point of intersection is in the load zone for 125 units. The intended load of 125 units is the same value as the value in the load zone so the load chart indicates that the load is at the maximum capacity of the machine.

Example 3

  • The weight of the intended load is 27 units.

  • The boom angle reference is 22 degrees.

  • The boom extension reference scale is approximately 66 percent between "D" and full extension. Full extension is "E" on the load chart.

With reference to the load chart, "Z" is the point of intersection for the values of the boom angle reference and the boom extension reference. This point of intersection is in the load zone for 20 units. The intended load of 27 units is greater than the value in the load zone so the load chart indicates that the load is beyond the capacity of the machine. The lift operation must not be attempted.

If the load chart indicates that the lift operation is within the capacity of the machine, attempt to make the operation but proceed with care. Remember that the load may weigh more than the estimate for the load. The load chart is for estimating the lift operation only.



Illustration 3g00913591
Typical Load Chart

Information System:

2003/10/27 D11R Implement Pump Update Provides Improved Quality and Fewer Leaks {5084}
988G Wheel Loader Seat
TH220B, TH330B and TH340B Telehandlers Boom Wear Pad Clearance - Inspect/Adjust
AD30 Underground Articulated Truck Machine Electrical System Actual Gear Indicator
AD30 Underground Articulated Truck Machine Electrical System Torque Converter Oil Temperature
AD30 Underground Articulated Truck Machine Electrical System Retarder
AD30 Underground Articulated Truck Machine Electrical System Engine Monitoring
AD30 Underground Articulated Truck Machine Electrical System Engine Shutdown
AD30 Underground Articulated Truck Machine Electrical System Engine Stop
AD30 Underground Articulated Truck Machine Electrical System Engine Start
988G Wheel Loader Warning Categories (Caterpillar Monitoring System)
980G Series II Wheel Loader Operator Controls
D6N Track-Type Tractor Power Train Final Drive, Steering Planetary, and Brake (Right Side) - Remove
D6N Track-Type Tractor Power Train Final Drive, Steering Planetary, and Brake (Right Side) - Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Operator Controls - Left Side Console for IT62G and 962G Parallel Lift Machines
IT28G Integrated Toolcarrier and 924G, 924Gz and 928G Wheel Loaders Window Wiper and Wiper Motor
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Power Train Transmission and Torque Converter - Remove
980G Series II Wheel Loader Monitoring System
TH220B, TH330B and TH340B Telehandlers Hydraulic System Location of Hydraulic Components
2003/06/09 A New Fuse Panel Is Used {1417}
Installation Instructions for the 2Q-8245 Fan Control Ar (Auto Reversing) (Kit){1386, 138R}
2003/06/01 SOLAS Requirement for Screening Fuel and Oil Line Connections on Marine Engines {1274, 1307}
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Operator Controls - Steering Control Console
963C Track-Type Loader Towing the Machine