IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Seat Caterpillar


Seat
`
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders [SEBU7018]
OPERATOR STATION
SEAT GP
120H and 135H Motor Graders Seat Belt
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Seat
1.1. Air Suspension
2.1. Mechanical Suspension

Note: The operator's seat that is provided with this machine is in compliance with the appropriate class of ISO 7096.

Adjust the seat in order to allow full travel of the pedals. Make the seat adjustments when the operator is sitting against the back of the seat.

Air Suspension



Illustration 1g00806971

Backrest (1) - Pull up on the backrest in order to remove extension (1).

Lumbar Support (2) - Push lever (2) backward in order to increase support to the lower back. Pull lever (2) forward in order to decrease support to the lower back. Release lever (2) in order to lock the seat into position.

Armrest (3) - Rotate knob (3) in order to adjust the angle of the armrest.

Seat Cushion Angle (4) - Pull lever (4) upward. Hold lever (4) upward and move the seat cushion to the desired angle. Release lever (4) in order to lock the seat cushion into position. The seat cushion can be adjusted to one of three positions.

Seat Backrest Angle Adjustment (5) - Pull lever (5) upward. Hold lever (5) upward. Adjust the backrest to the desired angle. Release lever (5) in order to lock the backrest into position.

Fore and Aft Position (6) - Pull lever (6) upward. Hold lever (6) upward and slide the seat forward or backward to the desired position. Release lever (6) in order to lock the seat into position.

Seat Height (7) - Pull knob (7) outward. Raise the seat to the desired height and release knob (7).

Mechanical Suspension



Illustration 2g00995631

Rotate knob (8) in order to adjust the angle of the armrest. Make this adjustment when the armrest is in the operating position.

Seat Backrest Angle Adjustment (9) - Pull up on lever (9). Hold the lever and adjust the backrest cushion angle to the desired angle. Release lever (9) in order to lock the backrest cushion into position.

Fore and Aft Position (10) - Pull up on lever (10) and hold the lever. Slide the seat forward or backward to the desired position. Release lever (10) in order to lock the seat into position.

Seat Suspension (11) - Turn knob (11) clockwise in order to increase the stiffness of the suspension. Turn knob (11) counterclockwise in order to decrease the stiffness of the suspension. Set the weight to the approximate weight setting. Do not turn the knob past the maximum weight setting or past the minimum weight setting.

Seat Cushion Angle (12) - Push lever (12) and raise the front of the seat cushion to the desired angle. To lower the cushion, push lever (12) and push down on the front of the seat cushion. Release the lever in order to lock the seat cushion into one of three positions.

Information System:

C4.4 (Mech) Industrial Engine Glow Plugs - Test
AD30 Underground Articulated Truck Machine Electrical System Rear Light/Backup Light
AD30 Underground Articulated Truck Machine Electrical System Directional Turn Signal and Hazard Flasher
AD30 Underground Articulated Truck Machine Electrical System Block Light/Rear Cab Flood Light
2003/05/05 A New Parking Brake Switch is Available {1408, 1435}
AD30 Underground Articulated Truck Machine Electrical System Head Light/Park Light
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Differential and Final Drive Oil Sample - Obtain
D5N Track-Type Tractor Monitoring System
2003/05/12 New Front Crankshaft Seals and New Rear Crankshaft Seals are Now in Production {1160, 1161}
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Cooling System Coolant Sample (Level 1) - Obtain
3500 Industrial Engines Accumulator Pressure - Test
IT62G Series II Integrated Toolcarrier and 950G Series II and 962G Series II Wheel Loaders Lift Kickout
2003/05/05 Improved Sealing of Cab Doors of Wheel Skidders {7308}
3054E Industrial Engine Fuel Injection Lines - Remove and Install
2003/05/05 A New Boot Eliminates Sticking of the Pilot Valve {5059}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Monitoring System
Inspection and/or Repair Procedure to Replace Broken Crankshafts in C-15, C-16, C15, 3406C, 3406E, and 3456 Engines{1202}
3054E Industrial Engine Fuel Injection Nozzles - Remove
992G Wheel Loader Machine Systems Bucket - Remove
3054E Engine for Caterpillar Built Machines Idler Gear - Remove and Install
D6R Series II and D7R Series II Track-Type Tractors AccuGrade Laser General Maintenance Information
AD30 Underground Articulated Truck Braking System Parking Brake System Pressure - Test
615C Series II Wheel Tractor-Scraper Air System and Brakes General Information
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Operator Controls - Right Side Console (Later Machines)