There are several specific safety messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all safety messages.
Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. When you clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety messages.
Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any AVSpare dealer can provide new safety messages.
Do Not Weld On The ROPS
Show/hide table
|
|
|
| Illustration 1 | g00722233 |
This safety message is located on the ROPS.
Show/hide table
|
|
|
| Illustration 2 | g00994335 |
Show/hide table
 |
|
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
|
No Hands
Show/hide table
|
|
|
| Illustration 3 | g00994338 |
This safety message is located on the legs of the stabilizers.
Show/hide table
|
|
|
| Illustration 4 | g00708923 |
Show/hide table
|
|
A crushing hazard exists when raising or lowering the stabilizers. Ensure that personnel stand clear when the stabilizers are being raised or lowered. Operating the stabilizers when personnel are nearby could result in personal injury or death. |
|
No Hands
Show/hide table
|
|
|
| Illustration 5 | g00994336 |
This safety message is located on both sides of the boom.
Show/hide table
|
|
|
|
| Illustration 6 | g00708923 |
Show/hide table
|
|
A crushing hazard exists when the boom sections are being retracted or extended. Stay clear of the boom when the machine is in operation. Failure to stay clear of the boom when the machine is operation can cause injury or death. |
|
Do not Stand Under the Load
Show/hide table
|
|
|
| Illustration 7 | g00722236 |
This safety message is located on both sides of the boom head.
Show/hide table
|
|
|
| Illustration 8 | g00708924 |
Show/hide table
|
|
Standing under or on forks present crush or fall hazards which may result in personal injury or death. Do not stand under or on forks. |
|
Jumper Cable Connections
Show/hide table
|
|
|
| Illustration 9 | g00722238 |
This safety message is located on the inside of the engine enclosure.
Show/hide table
|
|
|
| Illustration 10 | g00947488 |
Show/hide table
|
|
Improper jumper cable connections may cause an explosion resulting in personal injury. Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (−) cable from external source to starter negative (−) terminal. (If not equipped with starter negative terminal, connect to engine block.) Follow procedure in the Operation and Maintenance Manual. |
|
Inadvertent Attachment Movement
Show/hide table
|
|
|
| Illustration 11 | g00722239 |
This safety message is located on the boom head.
Show/hide table
|
|
|
| Illustration 12 | g00994339 |
Show/hide table
|
|
Inadvertent attachment movement can result in injury or death. Use only attachment which are fitted with devices that will prevent attachment movement in case of hydraulic line failure. |
|
Do Not Operate
Show/hide table
|
|
|
| Illustration 13 | g00715870 |
There are two locations for this safety message. One of the safety messages is located on the control panel of the access platform. The other safety message is located on the side panel in the cab.
Show/hide table
|
|
|
| Illustration 14 | g00788977 |
Show/hide table
|
|
DO NOT OPERATE OR WORK ON THIS MACHINE UNLESS YOU HAVE READ AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS IN THE OPERATION AND MAINTENANCE MANUALS. FAILURE TO FOLLOW THE INSTRUCTIONS OR HEED THE WARNINGS COULD RESULT IN INJURY OR DEATH. CONTACT ANY AVSpare DEALER FOR REPLACEMENT MANUALS. PROPER CARE IS YOUR RESPONSIBILITY. |
|
Manufactured Machines, or Properly Modified Machines for use with Access Platforms
Show/hide table
|
|
|
| Illustration 15 | g00722244 |
This safety message is located on the boom head and on the dash panel.
Show/hide table
|
|
|
| Illustration 16 | g00645510 |
Show/hide table
|
|
This machine was manufactured for, or has been properly modified for use with a AVSpare approved access platform.
Improper use of an access platform attachment could result in injury or death.
Do not use this machine with an access platform attachment until you have read, understood and can comply with the instructions and warnings given in the access platform Operation and Maintenance Manual. |
|
Machines that have not been Manufactured, or Modified for use with Access Platforms
Show/hide table
|
|
|
| Illustration 17 | g00722250 |
This safety message is located on the boom head and on the dash panel.
Show/hide table
|
|
|
| Illustration 18 | g00642677 |
Show/hide table
|
|
This machine was not manufactured for, and has not been modified for, use with an access platform attachment.
Use of an access platform attachment on a machine not manufactured or properly modified for use with such an attachment could result in injury or death.
Do not use this machine with an access platform attachment. |
|
Maximum Weight that is Allowed on Access Platform
Show/hide table
|
|
|
| Illustration 19 | g00715928 |
This safety message is located on the control panel of the access platform.
Show/hide table
|
|
|
| Illustration 20 | g00610161 |
Show/hide table
|
|
This attachment must not carry more than two operators. The maximum weight carried on the attachment, including operators, tools and equipment must not exceed 250 kg (550 lb).
Imposing excessive manual force on an access platform attachment could result in a tipping condition. This could result in personal injury or death. Manual force is defined as a force imposed on the access platform attachment by the operator pulling or pushing on an external object, or the access platform attachment contacting an external object. This access platform attachment must not be subjected to a manual force which is greater than 400 N (90 lb). |
|
Avoid Power Lines
Show/hide table
|
|
|
| Illustration 21 | g00715957 |
There are two locations for this safety message. One of the safety messages is located on the control panel of the access platform. The other safety message is located inside the cab above the windshield.
Show/hide table
|
|
|
| Illustration 22 | g00994337 |
Show/hide table
|
|
To avoid injury or death by electrocution keep machine and attachment at least 8 meters (25 ft) away from electric power lines. Always check for power lines before raising boom. |
|
Roading the Machine
Show/hide table
|
|
|
| Illustration 23 | g00722267 |
This safety message is located inside the cab to the right side of the front window. This safety message is used in UK applications only.
Show/hide table
|
|
|
| Illustration 24 | g00931533 |
Show/hide table
|
|
The coupler/work tool shall not be raised above this height during roading. Personal injury, property damage, or death may occur. |
|
Ether
Show/hide table
|
|
|
| Illustration 25 | g00722318 |
This safety message is located on the cover for the engine air filter and on the valve cover for the engine.
Show/hide table
|
|
|
| Illustration 26 | g00103679 |
Show/hide table
|
|
Explosion hazard! Do not use ether! This machine is equipped with an air inlet heater. Using ether can create explosions or fires that can cause personal injury or death. Read and follow the starting procedure in the Operation and Maintenance Manual. |
|
No Clearance
Show/hide table
|
|
|
| Illustration 27 | g00729264 |
This safety message is located on both sides of the self-tipping hopper.
Show/hide table
|
|
|
| Illustration 28 | g00547368 |
Show/hide table
|
|
No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation. |
|
Stay Clear
Show/hide table
|
|
|
| Illustration 29 | g00994389 |
This safety message is located on both sides of the work tools that are shown above.
Show/hide table
|
|
|
| Illustration 30 | g00994356 |
Show/hide table
|
|
Stay clear of this work tool during operation. Entanglement could result in personal injury or death. Flying objects from this work tool could result in personal injury or death. |
|
No Clearance
Show/hide table
|
|
|
| Illustration 31 | g00994352 |
This safety message is located on both sides of the work tools that are shown above.
Show/hide table
|
|
|
| Illustration 32 | g00544004 |
Show/hide table
|
|
No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation. |
|
