953C Track-Type Loader Engine Oil and Filter - Change Caterpillar


Engine Oil and Filter - Change
`
953C Track-Type Loader [SEBU7495]
LUBRICATION SYSTEM
FILTER GP-ENGINE OIL
953C Track-Type Loader Engine Oil and Filter - Change

------ WARNING! ------

Hot oil and components can cause personal injury.

Do not allow hot oil or components to contact skin.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.


Note: Be sure that you obtain an S·O·S oil sample before you drain the engine oil.



Illustration 1g00992826

  1. Remove the crankcase drain access cover, which is in the crankcase guard.

  2. Remove the section of hose from the tool box. Remove the crankcase drain plug. Install the hose. Open the valve. Allow the oil to drain into a suitable container.


    Illustration 2g00993617

  3. Open the access cover. Remove the crankcase oil filter element and discard the crankcase oil filter element properly. Make sure that all of the old filter seal is removed from the filter base.

  4. Apply a thin coat of oil to the new filter seals. Install the new crankcase oil filter elements by hand. When the gaskets contact the filter base, tighten the filter elements by an additional turn of 270 degrees. Rotation index marks are on the new filter elements. These rotation index marks are spaced at 90 degree intervals. Use these rotation index marks as a guide for proper tightening.

  5. Remove the hose. Close the valve. Return the hose to the tool box. Install the crankcase drain plug. Install the crankcase drain access cover.


    Illustration 3g00974903

  6. Remove the oil filler cap (2). Fill the crankcase with new oil. See Operation and Maintenance Manual, "Refill Capacities". Clean the oil filler cap and install the oil filler cap.

  7. Always measure the oil level with dipstick (1) in order to ensure that the correct amount of oil was added.

  8. On the dipstick, maintain the oil level between the "ADD" mark and "FULL" mark.

  9. Close the access cover.

Information System:

2003/04/14 There is New Information on the Oil Grade Plug {1000, 1348}
953C Track-Type Loader Engine Oil Level - Check
Bench Test Procedure for a 928G Wheel Loader andIT28G Integrated Toolcarrier Transmission with a Flexible Coupling Drive{3030, 3066, 3073}
525D, 535D, 545D, 555D Wheel Skidder Grapple Snubber - Inspect/Adjust
525B and 535B Wheel Skidders Additional Messages
525B and 535B Wheel Skidders Safety Messages
924G and 924GZ Wheel Loaders Machine Systems Main Control Valve - Assemble
924G and 924GZ Wheel Loaders Machine Systems Main Control Valve - Disassemble
3126B Engine for Caterpillar Built Machines System Configuration Parameters
AD30 Underground Articulated Truck Steering System Oil Filter - Replace
AD45B Underground Articulated Truck Oscillating Hitch - Adjust
2003/07/14 Correction to Systems Operation , "Selector and Pressure Control Valve" {3073, 3157}
525B and 535B Wheel Skidders Lifting and Tying Down the Machine
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Hydraulic and Transmission Oil Cooler - Remove
2003/04/14 Larger Fasteners Are Now Used on the Engine Bracket for the Governor Cable {1265, 1276}
973K Track-Type Loader Final Drive Oil - Change
D6N Track-Type Tractor Power Train Brake Control Valve - Disassemble
D6N Track-Type Tractor Power Train Brake Control Valve - Assemble
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Hydraulic and Transmission Oil Cooler - Install
AD30 Underground Articulated Truck Hydraulic Tank Screen - Clean
AD30 Underground Articulated Truck Reference Material
990 Series II Wheel Loader Machine Systems Bucket - Remove
Bench Test Procedure for a 950H, 962H, 966G, 966G Series 2, 966H, 972G, 972G Series 2, and 972H Wheel Loader Transmission and a R1600H Load Haul Dump {3030, 3066, 3073, 3101}
TH350B, TH355B, TH360B and TH460B Telehandlers Circuit Breakers - Test