There are several specific safety signs on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety signs.
Make sure that all of the safety signs are legible. Clean the safety signs or replace the safety signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety sign. Loose adhesive will allow the safety sign to fall.
Replace any safety sign that is damaged or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Any AVSpare dealer can provide new safety signs.
Do Not Operate
 | |
| Illustration 2 | g00872553 |
This warning is located in the cab.
 |
DO NOT OPERATE OR WORK ON THIS MACHINE UNLESS YOU HAVE READ AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS IN THE OPERATION AND MAINTENANCE MANUALS. FAILURE TO FOLLOW THE INSTRUCTIONS OR HEED THE WARNINGS COULD RESULT IN INJURY OR DEATH. CONTACT ANY AVSpare DEALER FOR REPLACEMENT MANUALS. PROPER CARE IS YOUR RESPONSIBILITY. |
 |
Improper Connections For Jump Start Cables
 | |
| Illustration 3 | g00992653 |
This warning is located on the right side of the radiator guard.
|
Improper jumper cable connections can cause an explosion resulting in personal injury. Batteries can be located in separate compartments. When using jumper cable always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal. (If not equipped with starter negative terminal, connect to engine block.) |
|
Do Not Weld On The ROPS
 | |
| Illustration 4 | g00872536 |
This warning is located on the ROPS.
|
Personal injury or death can result when voiding this certification. Structural damage, an overturn, modification, alteration, or improper repair can impair the ROPS structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. To avoid possible weakening of this ROPS, consult a AVSpare dealer before altering this ROPS in any way. The protection offered by this ROPS will be impaired if it has been subjected to structural damage. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
|
No Clearance
 | |
| Illustration 5 | g00874830 |
This warning is located on the machine at the center pivot.
|
No clearance for person in this area when machine turns. Severe injury or death from crushing could occur. |
|
Connect the steering frame lock between the front and the rear frame. Connect the steering frame lock before lifting. Connect the steering frame lock before transporting. Connect the steering frame lock before the machine is serviced near the articulation pivot.
Disconnect steering frame lock and secure the steering frame lock before resuming operation.
Compressed Spring
 | |
| Illustration 6 | g00872194 |
This warning is located on the parking brake actuator.
|
Do not attempt to remove spring(s), they are not serviceable. Do not cut, saw, torch or modify this chamber, serious injury or death may result. |
|
Pressurized System
 | |
| Illustration 7 | g00908550 |
This warning label is located on the bottom of the radiator access door.
|
Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure. |
|
Pressurized System
 | |
| Illustration 8 | g00908549 |
This warning label is located near the filler cap on the hydraulic tank.
|
At operating temperature, the hydraulic tank is hot and under pressure. Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin. Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly to relieve pressure. |
|
High Pressure Accumulator
 | |
| Illustration 9 | g00953733 |
Two of these warning labels are located on the mounting bracket of the brake accumulators.
|
High pressure cylinder. Parts can separate with explosive force if proper care is not used during disassembly. This can cause injury or death. Do not disassemble any part of this cylinder until you have read and understand the instructions given in the service manual. Observe the instructions given in the service manual. |
|
Water Cleaning System Under Pressure
 | |
| Illustration 10 | g00872190 |
This warning label is located near the filler plug on the water tank at the rear of the machine.
|
Do not remove the fill plug until the pressure in the water tank has been relieved. Personal injury may result. This fill plug has a cross drilled hole that allows the pressure to be relieved without disengaging the threads. Do not replace this fill plug with any other plug. |
|
Refer to Operation and Maintenance Manual, "Water Cleaning System" for more information.