938G Wheel Loader and IT38G Integrated Toolcarrier Seat Caterpillar


Seat
`
938G Wheel Loader and IT38G Integrated Toolcarrier [SEBU7037]
OPERATOR STATION
SEAT GP
120H and 135H Motor Graders Seat Belt
938G Wheel Loader and IT38G Integrated Toolcarrier Seat
1.1. Adjustable Armrest
2.1. Seat Adjustment

Note: The operator's seat that is provided with this machine is in compliance with the appropriate class of ISO 7096.

Adjust the seat in order to allow full travel of the pedals. Make the seat adjustments when the operator is sitting against the back of the seat.

Adjustable Armrest



Illustration 1g00102664

Rotate the knob in order to adjust the angle of the armrest. Make this adjustment when you are in the operating position.

Seat Adjustment



Illustration 2g00102665

Backrest Cushion Angle - Pull up on lever (1). Hold the lever and adjust the backrest cushion angle to the desired angle. Release lever (1) in order to lock the backrest cushion into position.

Fore and Aft Position - Pull up on lever (2) and hold the lever. Slide the seat forward or backward to the desired position. Release lever (2) in order to lock the seat into position.

Seat Suspension - Turn knob (3) clockwise in order to increase the stiffness of the suspension. Turn knob (3) counterclockwise in order to decrease the stiffness of the suspension. Set the weight to the approximate weight setting. Do not turn the knob past the maximum weight setting or past the minimum weight setting.



Illustration 3g00103893

Seat Cushion Angle - Push lever (4) and raise the front of the seat cushion to the desired angle. To lower the cushion, push lever (4) and push down on the front of the seat cushion. Release the lever in order to lock the seat cushion into one of three positions.



Illustration 4g00629607

Lumbar Support - Turn knob (5) counterclockwise in order to increase the support to the lower back. Turn knob (5) clockwise in order to decrease the support to the lower back.

Information System:

963C Track-Type Loader Power Train Transmission Stall - Test
AD30 Underground Articulated Truck Hydraulic System Oil Filter (Pilot) - Replace
AD30 Underground Articulated Truck Pressure Sensor (Transmission Oil) - Test - If Equipped
AD30 Underground Articulated Truck Radiator Core - Clean
AD30 Underground Articulated Truck Fuel Tank Cap and Strainer - Clean
973C Track-Type Loader Steel Mill Arrangement Maintenance Interval Schedule
2003/05/26 Improved Brakes Are Now Used {4131}
3054E Industrial Engine Crankshaft Rear Seal - Remove
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Starting
AD30 Underground Articulated Truck Hydraulic System Oil - Change
AD30 Underground Articulated Truck Fuel System Primary Filter (Water Separator) - Drain
834H Wheel Dozer and 836H Landfill Compactor Safety Messages
938G Wheel Loader and IT38G Integrated Toolcarrier Reference Material
3054E Industrial Engine Flywheel - Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Hydraulic System Troubleshooting
D6N Track-Type Tractor Power Train Steering Differential and Brake - Assemble
D6N Track-Type Tractor Power Train Axle - Remove and Install
953C Track-Type Loader Engine Starting with Jump Start Cables
CAES Installation For Wheel Loader{7604}
CAES Installation For Wheel Tractor Scraper{7604}
Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070}
953C Track-Type Loader Cooling System Extended Life Coolant - Change
953C Track-Type Loader Cooling System Water Temperature Regulator - Clean/Replace
953C Track-Type Loader Engine Oil Sample - Obtain