| |
| Illustration 1 | g00989356 |
| |
| Illustration 2 | g00989433 |
There are several specific safety messages on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety messages.
Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.
Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any AVSpare dealer can provide new safety messages.
This message is located in the cab.
| |
| Illustration 3 | g00788977 |
 |
|
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility. |
This safety message is located on the outside of the cab on the right side of the machine.
| |
| Illustration 4 | g00102169 |
|
|
Personal injury or death can result when voiding this certification. Structural damage, an overturn, modification, alteration, or improper repair can impair the ROPS structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. To avoid possible weakening of this ROPS, consult a AVSpare dealer before altering this ROPS in any way. The protection offered by this ROPS will be impaired if it has been subjected to structural damage. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
This machine has been certified to the standards that are listed on the certification plate. The maximum mass of the machine, which includes the operator and the attachments without a payload, should not exceed the mass on the certification plate.
This safety message is located near the cooling system pressure cap.
| |
| Illustration 5 | g00989359 |
|
|
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure. |
This safety message is located on the cooling system pressure cap.
| |
| Illustration 6 | g00921005 |
|
|
Hot parts or hot components can cause burns or personal injury. Do not allow hot parts or components to contact your skin. Use protective clothing or protective equipment to protect your skin. |
Improper Connections Of The Jump Start Cable (5)
| |
| Illustration 7 | g00038786 |
This safety message is located inside the battery compartment.
|
|
Improper jumper cable connections can cause an explosion resulting in personal injury. Batteries can be located in separate compartments. When using jumper cable always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (−) cable from external source to starter negative (−) terminal. (If not equipped with starter negative terminal, connect to engine block.) |
This safety message is located on the machine at the articulation joint.
| |
| Illustration 8 | g00038790 |
|
|
No clearance for person in this area when machine turns. Severe injury or death from crushing could occur. |
"Connect steering frame lock between front and rear frames before lifting, transporting, or servicing machine in articulation area."
"Disconnect lock and secure before resuming operation."
| |
| Illustration 9 | g00100419 |
This safety message is located on the ride control accumulator.
|
|
HIGH PRESSURE CYLINDER Do not remove any valve, hydraulic fitting, or valve core, nor disassemble any parts until pressure has been relieved or personal injury may occur. To relieve pressure: Shut off engine and wait five minutes for hydraulic system pressure to dissipate. Relieve gas pressure in the accumulator cylinder by opening the charging valve one turn only. Charge cylinder with dry nitrogen gas. Precharge pressure _______ PSI _______kPa. Service pressure (Operating-Loaded) ______PSI ______kPa. Minimum bursting pressure _____PSI _____kPa. See your AVSpare dealer for tools and detailed information required for charging cylinders. |
This safety message is located on the top surface of the hood.
| |
| Illustration 10 | g00989364 |
|
|
Do not attempt to remove spring(s), they are not serviceable. Do not cut, saw, torch or modify this chamber, serious injury or death may result. |
This message is located on the back of the mounting bracket by the serial number plate.
| |
| Illustration 11 | g00984073 |
|
|
Do not operate or work on this machine or work tool unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals and Owner's Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility. |
This message is located on the top of the broom on the right side of the broom.
|
| |
| Illustration 12 | g00984073 |
|
|
Do not operate or work on this machine or work tool unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals and Owner's Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility. |
This message is located on each side of the rear cover of the broom.
| |
| Illustration 13 | g00951565 |
|
|
No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation. |
This message is located on each side of the front cover of the broom.
| |
| Illustration 14 | g00984064 |
|
|
Stay clear of this work tool during operation. Entanglement could result in personal injury or death. Flying objects from this work tool could result in personal injury or death. |
This message is located on each side of the front cover of the broom.
| |
| Illustration 15 | g00989893 |
|
|
No clearance for person in this area during operation. Severe injury or death from crushing could occur. Stay away from the work tool while it is in operation. |