Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
`
AD30 Underground Articulated Truck
[SEBU7328]
AD30 Underground Articulated Truck
Differential and Final Drive Oil Level - Check
AD30 Underground Articulated Truck
Oscillating Hitch - Lubricate
POWER TRAIN
R2900 Load Haul Dump
Tire Inflation with Nitrogen
AD30 Underground Articulated Truck
Changing Direction and Speed
AD30 Underground Articulated Truck
Sampling Interval and Location of Sampling Valve
AD30 Underground Articulated Truck
Drive Shaft Universal Joints, Splines and Bearings - Inspect/Lubricate
AD30 Underground Articulated Truck
Screen (Torque Converter) - Clean
AD30 Underground Articulated Truck
Transmission Oil - Change
Show/hide table
 |
Crushing Hazard. Ensure that the engine start switch is in the OFF position, and that the parking brake is engaged before entering the articulation area. Failure to do so could result in serious injury or death. |
 |
Show/hide table
| NOTICE |
|---|
Check that the lines attached to all the remote grease fittings are undamaged. If the grease lines are split, grease will not reach the components that require lubricating. Machine damage will result. |
Inspect the drive shaft universal joints for wear, loose bolts, or missing bolts. Tighten loose bolts and replace missing bolts. Inspect the drive shaft splines and bearings for wear. Replace worn components.
Wipe off the fittings before any lubricant is applied.
- Apply lubricant through eight fittings in universal joints.
Show/hide table
 | |
| Illustration 1 | g00988851 |
- Apply lubricant through two fittings for the slip joint splines.
Show/hide table
 | |
| Illustration 2 | g00988860 |
Information System:
C7 Engines for Caterpillar Built Machines
Unit Injector Sleeve - Install
3500B Series II Marine Engines
Prelubrication System
C7 Engines for Caterpillar Built Machines
Unit Injector Sleeve - Remove
651E and 657E Wheel Tractor-Scrapers Hydraulic System
Cylinder Cycle Time - Check
C7 Engines for Caterpillar Built Machines
Crankshaft Gear - Remove and Install
C7 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Assemble
966F Series II Wheel Loader Power Train
Transmission Hydraulic Control Valve - Disassemble
C7 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Disassemble
Supplemental Documentation for the Payload Control System{7494}
613C Series II Wheel Tractor-Scraper Hydraulic System
Elevator Circuit
613C Series II Wheel Tractor-Scraper Hydraulic System
Ejector Circuit
Installation of Direct Conversion Center Tread Idlers {4159}
Installation of 9SU (S/N: 9RP; T9J) and 9U (S/N: 9MP; T9H) Bulldozer with a Single Tilt Cylinder {5104, 6050}
Bench Test Procedure for Hydraulic Piston Pumps{3203, 5070}
2003/03/31
Correction to Disassembly and Assembly , "Axle Shaft Assemblies" {3259}
2003/03/31
Correction to Disassembly and Assembly , "Gear Pump (Axle Oil Cooler) - Remove and Install" {5073}
G3500B Engines
Start/Stop Control
AD30 Underground Articulated Truck
Oscillating Hitch - Lubricate
C7 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove
3054E Industrial Engine
Housing (Front) - Install
C7 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
651E and 657E Wheel Tractor-Scrapers Power train
Power Train Troubleshooting
2003/03/31
Correction to Disassembly and Assembly , "Piston Pump (Steering) - Disassemble" {4306, 5070}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Safety Messages