Hydraulic System Oil Sample - Obtain
`
938G II Wheel Loader and IT38G II Integrated Toolcarrier
[SEBU7581]
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Differential and Final Drive Oil Sample - Obtain
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Cooling System Coolant Level - Check
HYDRAULIC SYSTEM
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Hydraulic System Oil Sample - Obtain
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
- Operate the machine for a few minutes before obtaining the oil sample. Operate the hydraulic controls. This will thoroughly mix the hydraulic oil for a more accurate sample.
Show/hide table
Illustration 1 g00987284 - Open the engine access door on the left side of the machine. The in-line sampling valve is located near the top of the hydraulic oil cooler.
Show/hide table
Illustration 2 g00987285 Top view of the machine - Use the in-line sampling valve in order to obtain a sample of hydraulic oil.
- Close the engine access door.
Information System:
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Differential and Final Drive Oil Sample - Obtain
3046 Engine for Caterpillar Built Machines
Engine Oil Pump - Inspect
938G II Wheel Loader and IT38G II Integrated Toolcarrier
Engine Oil Sample - Obtain
963C Track-Type Loader
Belt - Inspect/Replace
3046 Engine for Caterpillar Built Machines
Engine Oil Pressure - Test
963C Track-Type Loader
Circuit Breakers and Fuses - Reset/Replace
525B Wheel Skidder, 535B Wheel Skidder and 545 Wheel Skidder Grapple
Hydraulic Rotator - Continuous Rotation Grapple
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement
Radiator and Fan Group - Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Starting
2004/08/23
New Exhaust Tubes and Heat Shields are Now Used {1050, 1061, 1067}
953C Track-Type Loader
Safety Messages
3508B Engine
Radiator and Cooling System - Test
3044C Industrial Engine and Engines for Caterpillar Built Machines
Engine Oil Cooler - Inspect
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train
Drive and Steering Axle (Rear) - Remove
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train
Drive and Steering Axle (Rear) - Install
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train
Drive and Steering Axle (Front) - Remove
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train
Drive and Steering Axle (Front) - Install
953C Track-Type Loader
Daily Inspection
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valves - Remove and Install
980G Series II Wheel Loader Electrohydraulic System
Pump Performance (Pilot and Braking) - Test
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Guides - Remove and Install
953C Track-Type Loader
Engine Starting
C7 Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Seat Inserts - Remove and Install
953C Track-Type Loader
Emissions Certification Film