963C Track-Type Loader Circuit Breakers and Fuses - Reset/Replace Caterpillar


Circuit Breakers and Fuses - Reset/Replace
`
1.1. Reset Circuit Breakers
2.1. Replace Fuses
3.2. (S/N: BBD1-1999)
4.2. (S/N: BBD2000-Up)

Reset Circuit Breakers



Illustration 1g00953407

The circuit breakers are located behind the console panel on the left side of the machine.



Illustration 2g00960192

Circuit Breaker Reset - Push in the button in order to reset the circuit breaker. If the electrical system is working properly, the button will remain depressed. If the button does not remain depressed, check the appropriate electrical circuit. Repair the electrical circuit, if necessary.

Replace Fuses



Illustration 3g00954503

The fuses are located inside the left hand console cover. Remove the two screws in order to remove the cover.

Fuses - Fuses protect the electrical system from damage that is caused by overloaded electrical circuits. Replace a fuse if the element separates. If the fuse of a particular electrical system requires frequent replacement, check the electrical circuit. Repair the electrical circuit, if necessary.


NOTICE

Always replace fuses with the same type and capacity fuse that was removed. Otherwise, electrical damage could result.



NOTICE

If it is necessary to replace fuses frequently, an electrical problem may exist.

Contact your AVSpare dealer.


(S/N: BBD1-1999)



Illustration 4g00954489

Spare (1) - 15 Amp

Spare (2) - 10 Amp

Spare (3) - 15 Amp

Spare (4) - 10 Amp

Front and Rear Windshield Wiper/Washer (5) - 15 Amp

Electronic Monitoring System (6) - 10 Amp

Transmission (7) - 10 Amp

Spare (8) - 15 Amp

Air Conditioner (9) - 15 Amp

Bucket (10) - 10 Amp

Seat (11) - 10 Amp

Beacon (12) - 10 Amp

Horn (13) - 10 Amp

Note: The dome lamp and the display backlight on the monitoring system also use this fuse.

Electronic Fuel Injection (14) - 15 Amp

Flood Lamp Group (15) - 15 Amp

Trailer Connector and Alarm (16) - 10 Amp

Note: The machine security system and the product link also use this fuse.

12 Volt Power Terminal (17) - 15 Amp

Note: The power converter and the radio also use this fuse.

Key Start Switch (18) - 10 Amp

Spare (19) - 115 Amp

Spare (20) - 10 Amp

(S/N: BBD2000-Up)



Illustration 5g01328773

Auxiliary circuit (1) - 15 Amp

Air conditioning (2) - 15 Amp

Spare (3) - 15 Amp

Spare (4) - 10 Amp

Front and Rear Windshield Wiper/Washer (5) - 15 Amp

Electronic Monitoring System (6) - 10 Amp

Transmission (7) - 10 Amp

Spare (8) - 15 Amp

Spare (9) - 15 Amp

Bucket (10) - 10 Amp

Seat (11) - 10 Amp

Beacon (12) - 10 Amp

Horn (13) - 10 Amp

Note: The dome lamp and the display backlight on the monitoring system also use this fuse.

Electronic Fuel Injection (14) - 15 Amp

Flood Lamp Group (15) - 15 Amp

Trailer Connector and Alarm (16) - 10 Amp

Note: The machine security system and the product link also use this fuse.

12 Volt Power Terminal (17) - 15 Amp

Note: The power converter and the radio also use this fuse.

Key Start Switch (18) - 10 Amp

Spare (19) - 15 Amp

Spare (20) - 10 Amp

Information System:

525B Wheel Skidder, 535B Wheel Skidder and 545 Wheel Skidder Grapple Hydraulic Rotator - Continuous Rotation Grapple
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Radiator and Fan Group - Install
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Starting
2004/08/23 New Exhaust Tubes and Heat Shields are Now Used {1050, 1061, 1067}
953C Track-Type Loader Safety Messages
3508B Engine Radiator and Cooling System - Test
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Rated Load
D6N Track-Type Tractor Power Train Final Drive - Install
D6N Track-Type Tractor Power Train Final Drive - Remove
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Radiator and Fan Group - Remove
3034 Engine for Caterpillar Built Machines Crankshaft Main Bearings - Remove
539 Knuckleboom Loader Operation
3046 Engine for Caterpillar Built Machines Engine Oil Pressure - Test
963C Track-Type Loader Belt - Inspect/Replace
938G II Wheel Loader and IT38G II Integrated Toolcarrier Engine Oil Sample - Obtain
3046 Engine for Caterpillar Built Machines Engine Oil Pump - Inspect
938G II Wheel Loader and IT38G II Integrated Toolcarrier Differential and Final Drive Oil Sample - Obtain
938G II Wheel Loader and IT38G II Integrated Toolcarrier Hydraulic System Oil Sample - Obtain
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Cooler - Inspect
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Rear) - Remove
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Rear) - Install
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Front) - Remove
TH350B, TH355B, TH360B, TH460B and TH560B Telehandlers Power Train Drive and Steering Axle (Front) - Install
953C Track-Type Loader Daily Inspection