IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Rated Load Caterpillar


Rated Load
`
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders [SEBU7018]
WORK TOOLS
ARM GP
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Rated Load
1.1. Rated Load for the Bucket
2.1. Rated Load for the Pallet Fork
3.1. Rated Load for the Logging Fork
4.1. Rated Load for the Material Handling Arm

------ WARNING! ------

Failure to comply to the rated load can cause possible personal injury or property damage. Review the rated load of a particular work tool before performing any operation. Make adjustments to the rated load as necessary for non-standard configurations.


Note: Rated loads should be used as a guide. Attachments, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on rated loads. The operator is responsible for being aware of these effects.

Rated loads are based upon a standard machine with the following conditions:

  • proper lubricants

  • full fuel tank

  • enclosed ROPS

  • 80 kg (176 lb) operator

  • 26.5x25 14PR L-2 tires or equivalent

Rated loads will vary for different attachments. Consult your AVSpare dealer about the rated load for specific attachments.

The rated operating load is defined by SAE "J818" (May 1987) and by the ISO 5998 (1986) as 50% of the full turn static tipping load.

For North America, the rated operating load is defined by SAE "J1197" (February 1991) as 50% of the full turn static tipping load.

For Europe, the rated operating load is defined by CEN "474-3" as 60% of the full turn static tipping load.

Rated Load for the Bucket



Illustration 1g00104485

The dump clearance and the reach are given for each bucket at maximum lift height and at a 45 degree dumping angle. Dump clearance (A) is measured from the ground to the bucket edge. Reach (B) is measured from the front of the front tire to the bucket edge.

The following tables provide the rated operating loads for the standard machine configuration with a bucket.

Table 1
Rated Load (950G Buckets) 
Part Number (Bucket)  Ground Engaging Tools  Rated Volume  Rated Operating Load  Dump Clearance
A 
Reach
B 
130-8285  General Purpose With Teeth  2.5 m3 (3.25 yd3)  5270 kg (11618 lb)  2740 mm (108 inch)  1316 mm (51.8 inch) 
General Purpose With Teeth and Segments 2.7 m3 (3.5 yd3)  5270 kg (11618 lb)  2740 mm (108 inch)  1316 mm (51.8 inch) 
General Purpose With a Bolt-On Cutting Edge 2.7 m3 (3.5 yd3)  5270 kg (11618 lb)  2854 mm (112 inch)  1216 mm (47.9 inch) 
130-8286  General Purpose With Teeth  2.7 m3 (3.5 yd3)  5270 kg (11618 lb)  2696 mm (106 inch)  1350 mm (53.1 inch) 
General Purpose With Teeth and Segments 2.9 m3 (3.75 yd3)  5270 kg (11618 lb)  2696 mm (106 inch)  1350 mm (53.1 inch) 
General Purpose With a Bolt-On Cutting Edge 2.9 m3 (3.75 yd3)  5270 kg (11618 lb)  2810 mm (110 inch)  1250 mm (49.2 inch) 
130-8287  General Purpose With Teeth  2.9 m3 (3.75 yd3)  5270 kg (11618 lb)  2654 mm (104 inch)  1384 mm (54.5 inch) 
General Purpose With Teeth and Segments 3.1 m3 (4 yd3)  5270 kg (11618 lb)  2654 mm (104 inch)  1384 mm (54.5 inch) 
General Purpose With a Bolt-On Cutting Edge 3.1 m3 (4 yd3)  5270 kg (11618 lb)  2766 mm (109 inch)  1286 mm (50.6 inch) 
130-3069  Material Handler With Teeth  2.9 m3 (3.75 yd3)  5270 kg (11618 lb)  2703 mm (106 inch)  1233 mm (48.5 inch) 
Material Handler With Teeth and Segments 3.1 m3 (4 yd3)  5270 kg (11618 lb)  2742 mm (108 inch)  1250 mm (49.2 inch) 
Material Handler With a Bolt-On Cutting Edge 3.1 m3 (4 yd3)  5270 kg (11618 lb)  2814 mm (111 inch)  1160 mm (45.7 inch) 
130-3070  Material Handler With Teeth  3.1 m3 (4 yd3)  5270 kg (11618 lb)  2663 mm (105 inch)  1286 mm (50.6 inch) 
Material Handler With Teeth and Segments 3.3 m3 (4.3 yd3)  5610 kg (12368 lb)  2663 mm (105 inch)  1286 mm (50.6 inch) 
Material Handler With a Bolt-On Cutting Edge 3.3 m3 (4.3 yd3)  5610 kg (12368 lb)  2777 mm (109 inch)  1196 mm (47.1 inch) 
113-3245  Spade Rock With a Bolt-On Cutting Edge  2.7 m3 (3.5 yd3)  5270 kg (11618 lb)  2762 mm (109 inch)  1299 mm (51.1 inch) 
130-8289  Spade Rock With Short Tips  2.7 m3 (3.5 yd3)  5270 kg (11618 lb)  2699 mm (106 inch)  1353 mm (53.3 inch) 

Table 2
Rated Load (962G Buckets) 
Part Number (Bucket)  Ground Engaging Tools  Rated Volume  Rated Operating Load  Dump Clearance
A 
Reach
B 
148-7242  General Purpose With Teeth  3.1 m3 (4 yd3)  5610 kg (12368 lb)  2837 mm (112 inch)  1350 mm (53.1 inch) 
General Purpose With Teeth and Segments 3.3 m3 (4.25 yd3)  5610 kg (12368 lb)  2837 mm (112 inch)  1350 mm (53.1 inch) 
General Purpose With a Bolt-On Cutting Edge 3.3 m3 (4.25 yd3)  5610 kg (12368 lb)  2950 mm (116 inch)  1252 mm (49.3 inch) 
130-3075  General Purpose With Teeth  3.6 m3 (4.75 yd3)  5610 kg (12368 lb)  2774 mm (109 inch)  1324 mm (52.1 inch) 
General Purpose With Teeth and Segments 3.8 m3 (5 yd3)  5610 kg (12368 lb)  2774 mm (109 inch)  1324 mm (52.1 inch) 
General Purpose With a Bolt-On Cutting Edge 3.8 m3 (5 yd3)  5610 kg (12368 lb)  2888 mm (113 inch)  1324 mm (52.1 inch) 
130-8287  General Purpose With Teeth  2.9 m3 (3.75 yd3)  5610 kg (12368 lb)  2783 mm (109 inch)  1316 mm (51.8 inch) 
General Purpose With Teeth and Segments 3.1 m3 (4 yd3)  5610 kg (12368 lb)  2783 mm (109 inch)  1316 mm (51.8 inch) 
General Purpose With a Bolt-On Cutting Edge 3.1 m3 (4 yd3)  5610 kg (12368 lb)  2986 mm (118 inch)  1218 mm (47.9 inch) 
130-3071  Material Handler With Teeth  3.3 m3 (4.25 yd3)  5610 kg (12368 lb)  2829 mm (111 inch)  1271 mm (50.0 inch) 
Material Handler With Teeth and Segments 3.5 m (4.5 yd)  5610 kg (12368 lb)  2829 mm (111 inch)  1271 mm (50.0 inch) 
Material Handler With a Bolt-On Cutting Edge 3.1 m3 (4 yd3)  5270 kg (11618 lb)  2814 mm (110 inch)  1160 mm (45.7 inch) 
130-3070  Material Handler With Teeth  3.1 m3 (4 yd3)  5610 kg (12368 lb)  2866 mm (113 inch)  1236 mm (48.6 inch) 
Material Handler With Teeth and Segments 3.3 m3 (4.25 yd3)  5610 kg (12368 lb)  2866 mm (113 inch)  1236 mm (48.6 inch) 
Material Handler With a Bolt-On Cutting Edge 3.3 m3 (4.25 yd3)  5610 kg (12368 lb)  2979 mm (117 inch)  1236 mm (48.6 inch) 
148-7244  Spade Rock With a Bolt-On Cutting Edge  3.1 m3 (4 yd3)  5610 kg (12368 lb)  2902 mm (114 inch)  1311 mm (51.6 inch) 
148-7246  Spade Rock With Short Tips  3.1 m3 (4 yd3)  5610 kg (12368 lb)  2843 mm (112 inch)  1347 mm (53.0 inch) 

Table 3
Rated Load (IT62G Buckets) 
Part Number (Bucket)  Ground Engaging Tools  Rated Volume  Rated Operating Load  Dump Clearance
A 
Reach
B 
111-5742  Material Handler  3.7 m3 (4.8 yd3)  5610 kg (12368 lb)  2840 mm (112 inch)  1240 mm (48.8 inch) 

Rated Load for the Pallet Fork



Illustration 2g00986865

The clearance and the reach are given for each implement at the maximum lift height. Clearance (C) is measured from the ground to the bottom edge of the implement. Reach (D) is measured from the front of the front tire to the front vertical edge of the implement.

The following table provides the rated operating loads for the standard machine (North American configuration).

Table 4
Rated Load (IT62G Pallet Fork) 
Part Number (Pallet Fork)  115-7448 
Maximum Clearance
C 
3790 mm (149 inch) 
Full Reach
D 
1117 mm (44 inch) 
Overall Length With Fork on Ground  8755 mm (345 inch) 
Maximum Load  4141 kg (9129 lb) 

Reference: Refer to Special Publication, GELQ0149, "Wheel Loader Fork Application Guide" for the rated loads of other machine configurations.

Rated Load for the Logging Fork



Illustration 3g00986872

The following table provides the rated operating load for the standard machine configuration with a logging fork.

Table 5
Rated Load (IT62G Logging Fork) 
Operating Load  5990 kg (13205 lb) 
Load Carrying Capacity
E 
2.4 m2 (2.88 yd2) 
Maximum Height for Unloading
F 
4450 mm (175 inch) 
Maximum Opening
G 
2820 mm (111 inch) 

Rated Load for the Material Handling Arm



Illustration 4g00986890

The placement height is measured from the ground to the chain hook. The reach is measured from the center of the front tire to the chain hook. These measurements are given for a material handling arm that is at highest position (1) and at lowest position (2). The operating load is given for a machine that is articulated by 40 degrees.

The following table provides the rated operating loads for the standard machine configuration with a material handling arm.

Table 6
Rated Load (IT62G Material Handling Arm) 
Length of Material Handling Arm  Rated Operating Load  Placement Height at Highest Position  Reach at Highest Position  Placement Height at Lowest Position  Reach at Lowest Position 
Retracted
3085 kg (6801 lb)  5775 mm (227 inch)  2545 mm (100 inch)  1485 mm (58.5 inch)  2720 mm (107 inch) 
Mid-Position
2626 kg (5789 lb)  6340 mm (250 inch)  3110 mm (122 inch)  1970 mm (77.6 inch)  3355 mm (132 inch) 
Extended
2288 kg (5044 lb)  6910 mm (272 inch)  3670 mm (144 inch)  2460 mm (96.8 inch)  3987 mm (157 inch) 

Information System:

D6N Track-Type Tractor Power Train Final Drive - Install
D6N Track-Type Tractor Power Train Final Drive - Remove
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Radiator and Fan Group - Remove
3034 Engine for Caterpillar Built Machines Crankshaft Main Bearings - Remove
539 Knuckleboom Loader Operation
C4.4 (Mech) Industrial Engine Valve Guide - Inspect
963C Track-Type Loader Machine Systems Track
TH210 and TH215 Telehandlers Access Doors and Covers
3034 Engine for Caterpillar Built Machines Crankshaft Main Bearings - Install
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Fuel Tank - Install
D6N Track-Type Tractor Power Train Final Drive, Steering Clutch and Brake - Install
D6N Track-Type Tractor Power Train Final Drive, Steering Clutch and Brake - Remove
3508B Engine Radiator and Cooling System - Test
953C Track-Type Loader Safety Messages
2004/08/23 New Exhaust Tubes and Heat Shields are Now Used {1050, 1061, 1067}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Starting
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Engine Supplement Radiator and Fan Group - Install
525B Wheel Skidder, 535B Wheel Skidder and 545 Wheel Skidder Grapple Hydraulic Rotator - Continuous Rotation Grapple
963C Track-Type Loader Circuit Breakers and Fuses - Reset/Replace
3046 Engine for Caterpillar Built Machines Engine Oil Pressure - Test
963C Track-Type Loader Belt - Inspect/Replace
938G II Wheel Loader and IT38G II Integrated Toolcarrier Engine Oil Sample - Obtain
3046 Engine for Caterpillar Built Machines Engine Oil Pump - Inspect
938G II Wheel Loader and IT38G II Integrated Toolcarrier Differential and Final Drive Oil Sample - Obtain