TH560B Telehandler Additional Messages Caterpillar


Additional Messages
`

There are several specific messages on these machines. The exact location of the messages and the description of the messages are reviewed in this section. Please become familiarized with all messages.

Make sure that all of the messages are legible. Clean the messages or replace the messages if the words or images are unreadable. When you clean the messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.

Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any AVSpare dealer can provide new messages.



Illustration 1g01213252


Illustration 2g01213279


Illustration 3g01212920

Emergency Lower System (1)

If equipped, this message is located on the emergency lower module. The emergency lower module is located at the rear right hand side of the machine.



Illustration 4g01212935

Do not operate this machine or use this machine unless you understand the instructions in the “Procedure for Retracting and Lowering the Boom with the Emergency Lower System (If Equipped)” topic in Operation and Maintenance Manual, "Equipment Lowering with Loss of Hydraulic Power".

Air Cleaner (2)

This message is located on the cover for the air cleaner.



Illustration 5g00931688

Clean the filter element or replace the filter element when the restriction indicator shows red. Refer to Operation and Maintenance Manual, "Engine Air Filter Primary Element - Clean/Replace" and Operation and Maintenance Manual, "Engine Air Filter Secondary Element - Repace" for more information.

Auxiliary Hydraulics (3)

This message is located on the left side of the boom head.



Illustration 6g00934458

Use only work tools that are approved by AVSpare. Refer to the topic “Auxiliary Hydraulic Connections” in Operation and Maintenance Manual, "Work Tools" for more information.

Access Platform (4)

This message is located on the panel at the right side of the operator station.



Illustration 7g00934440

This machine is equipped for use with an access platform which has been approved by AVSpare. Do not operate this machine or use this machine with an access platform unless you understand the instructions in Operation and Maintenance Manual, SEBU7999, "THP10 Series II and THP24S Series II Access Platform for Series B Telehandlers". Improper use of the access platform could result in injury or death.

Alternate Exit (5)

This message is located on the rear window of the cab.



Illustration 8g00931915

If the primary exit is blocked, exit the machine through the rear window. Use the ring on the rear window latch in order to pull out the retaining pin. This action will unlock the rear window.

Transmission and Hydraulic Oil (6)

If equipped, this message is located next to the sight gauge for the transmission and hydraulic oil.



Illustration 9g01059267

Check the transmission and hydraulic oil when the oil is warm. Do not add oil when the system is cold. If the system is cold and you add oil, you can overfill the system. This could cause machine damage. Refer to Operation and Maintenance Manual, "Transmission and Hydraulic Oil Level - Check" for the correct procedure.

Air Conditioner (7)

On machines that are equipped with an air conditioner, this label is located behind the protection cover at the rear of the door.



Illustration 10g00934175

Do not work on the air conditioning system until you have read the service manual and you understand the service manual.

Tire Pressures (8)

This message is located behind the protection cover on the left side of the cab.



Illustration 11g00931919

Personal injury can result from improper tire inflation. Refer to Operation and Maintenance Manual, "Tire Inflation Information" for more information.

Machine Security System (9)

If equipped, this message is located on the left side of the steering column ahead of the engine start switch.



Illustration 12g00951606

This machine is equipped with a security system. Read the Operation and Maintenance Manual before you operate the machine.

Information System:

938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Steering Control Valve - Remove
2005/04/11 Correction to Operation and Maintenance Manual , "Drive Shaft Support Bearing - Lubricate" {3267}
2003/03/17 Correction to Operation and Maintenance Manual , "Lubricant Viscosities" {7581}
3034 Engine for Caterpillar Built Machines Connecting Rod Bearings - Install - Fractured Connecting Rod
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 1869 - FMI 04
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 1869 - FMI 03
D11R Track-Type Tractor Engine and Machine Warm-Up
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 0682 - FMI 06
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 0682 - FMI 05
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System MID 079 - CID 0682 - FMI 03
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Metering Pump (HMU) - Install
3034 Engine for Caterpillar Built Machines Connecting Rod Bearings - Install - Serrated Connecting Rod
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems Steering Control Valve - Install
3034 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove - Serrated Connecting Rod
3034 Engine for Caterpillar Built Machines Connecting Rod Bearings - Remove - Fractured Connecting Rod
TH210 and TH215 Telehandlers Lubricant Viscosities
AD30 Underground Articulated Truck Braking System Brake Control Valve (Service)
AD30 Underground Articulated Truck Braking System Brake Control Valve (Parking)
950G Series II Wheel Loader and 962G Series II Wheel Loader Electrohydraulic System Torque Converter Stall and Implement Pump Double Stall - Test
3044C Industrial Engine and Engines for Caterpillar Built Machines Fuel System
3046 Engine for Caterpillar Built Machines Air Inlet and Exhaust System
3044C Industrial Engine and Engines for Caterpillar Built Machines Lubrication System
3044C Industrial Engine and Engines for Caterpillar Built Machines Basic Engine