Hub Oil (Flexxaire Fan) - Change - If Equipped
`
D10R Track-Type Tractor
[SEBU7244]
D10R Track-Type Tractor
Hydraulic System Oil Filter (Pilot) - Replace
D10R Track-Type Tractor
Maintenance Interval Schedule
COOLING SYSTEM
FAN GP
D10R Track-Type Tractor
Hub Oil (Flexxaire Fan) - Change - If Equipped
Show/hide table
 |
|
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| |
| Illustration 1 | g00563726 |
|
Typical location of the oil drain plug | |
- Rotate the hub until the oil drain plug is facing downward.
Show/hide table
Illustration 2 g00984461 - Remove oil filler plug (1) and oil level plug (2).
- Remove the oil drain plug and allow the oil to drain into a suitable container.
Show/hide table
Illustration 3 g00984463 - Apply 6V-6640 Sealant to the threads (A) of the oil drain plug and replace the plug.
- Verify that oil filler plug (5) is facing upward.
- Fill the hub with new oil. Refer to Operation and Maintenance Manual, "Capacities (Refill)" and Operation and Maintenance Manual, "Capacities (Refill)"for additional information.
- Add oil until oil begins to drip from oil level hole (6).
- Apply 6V-6640 Sealant to the threads of the oil level plug and the oil filler plug. Reinstall the plugs.
- Check for any leaks and make any necessary repairs before operating the fan.
Information System:
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Selector and Pressure Control Valve (Pilot) - Remove and Install
D6N Track-Type Tractor Machine Systems
Bulldozer Lift Cylinder (VPAT) - Remove and Install
D6N Track-Type Tractor Machine Systems
Bulldozer Tilt Cylinder (VPAT) - Remove and Install
D6N Track-Type Tractor Machine Systems
Sweeps - Remove and Install
651E and 657E Wheel Tractor-Scrapers Wheel Scraper Power Train
Scraper Wiring Group
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Main Control Valve - Remove
TH350B, TH360B, TH460B and TH560B Telehandlers Engine Supplement
Engine Mount (Rear) - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control (Joystick) - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control (Joystick) - Disassemble
2003/03/10
A Change to the Transmission Cover Requires a New Tube Assembly {3064}
TH350B, TH360B, TH460B and TH560B Telehandlers Engine Supplement
Engine Mount (Rear) - Remove
TH210 and TH215 Telehandlers Machine Systems
Trailer Brake Valve (Hydraulic) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Main Control Valve - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pressure Reducing Valve (Traction Control System) - Remove and Install
3034 Engine for Caterpillar Built Machines
Pistons and Connecting Rods - Remove - Serrated Connecting Rod
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control (Joystick) - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Diverter Valve (Quick Coupler) - Remove and Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Heater Coil - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Pilot Operated Hydraulic Control (Joystick) - Install
2003/03/10
A New Dust Ejector Group for the Exhaust Prevents Loading on the Muffler {1068}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Heater Coil - Install
3034 Engine for Caterpillar Built Machines
Crankshaft - Install
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Blower Motor (Air Conditioner, Heater) - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Blower Motor (Air Conditioner, Heater) - Install