There are several specific safety messages on this machine. The exact location of the safety messages and the description of the safety messages are reviewed in this section. Please become familiarized with all safety messages.
Make sure that all of the safety messages are legible. Clean the safety messages or replace the safety messages if you cannot read the words. Replace the safety messages if the illustrations are not legible. When you clean the safety messages, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety message. Loose adhesive will allow the safety message to fall.
Replace any safety message that is damaged, or missing. If a safety message is attached to a part that is replaced, install a safety message on the replacement part. Any AVSpare dealer can provide new safety messages.
| |
| Illustration 1 | g01213283 |
This message is on the left side of the cab.
| |
| Illustration 2 | g01213284 |
 |
|
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your Cat dealer for replacement manuals. Proper care is your responsibility. |
Do Not Weld or Drill the ROPS (2)
This message is on the ROPS.
| |
| Illustration 3 | g01213285 |
|
|
Structural damage, an overturn, modification, alteration, or improper repair, can impair this structure's protective capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
Do Not Weld or Drill the FOPS (3)
This message is on the outside of the right side of the cab.
| |
| Illustration 4 | g01213286 |
|
|
Structural damage, an overturn, modification, alteration, or improper repair, can impair this structure's protective capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
Hot Coolant Under Pressure (4)
This message is on the underside of the access cover for the radiator cap.
| |
| Illustration 5 | g00782457 |
|
|
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure. |
This message is on the engine.
| |
| Illustration 6 | g01213287 |
|
|
Electrical shock hazard. The electronic unit injector system uses 90-120 volts. |
Improper Connections for Jump Start Cables (6)
This message is on the underside of each battery compartment cover.
| |
| Illustration 7 | g01213289 |
|
|
Improper jumper cable connections can cause explosion resulting in personal injury. If equipped, use the auxiliary starting receptacle to insure proper cable connection. Follow procedure in the Operation and Maintenance Manual. Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid, then, negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block or a designated ground stud). Follow procedure in the Operation and Maintenance Manual. |
This message is on the end of the tube of the front track roller frames.
| |
| Illustration 8 | g00934226 |
|
|
Recoil spring force, if not relieved, can result in personal injury or death. Relieve spring force before removing the threaded retainer, performing repairs on the recoil spring housing, or removing the recoil spring. Consult a AVSpare dealer for disassembly instructions. |
This message is on the track roller frame.
| |
| Illustration 9 | g01213292 |
|
|
Personal injury or death can result from grease under pressure. Grease coming out of the relief valve under pressure can penetrate the body causing injury or death. Do not watch the relief valve to see if grease is escaping. Watch the track or track adjustment cylinder to see if the track is being loosened. Loosen the relief valve one turn only. If track does not loosen, close the relief valve and contact your AVSpare dealer. |
This message is on the underside of the cover for the guides on the track roller frames.
| |
| Illustration 10 | g01213293 |
|
|
Stop disassembly if evidence of a crack exists in the tube or slot beneath this guide. A cracked tube can break suddenly expelling pieces with great force that could result in serious injury or death. Contact a AVSpare dealer for special disassembly instructions. |