Caterpillar Approved Work Tools
`
TH220B, TH330B and TH340B Telehandlers
[SEBU7708]
TH220B, TH330B and TH340B Telehandlers
Tire Shipping Pressure
TH220B, TH330B and TH340B Telehandlers
Boom Wear Pad Clearance - Inspect/Adjust
WORK TOOLS
TH220B, TH330B and TH340B Telehandlers
Plate Locations and Film Locations
TH220B, TH330B and TH340B Telehandlers
Caterpillar Approved Work Tools
TH220B, TH330B and TH340B Telehandlers
Work Tools
Show/hide table
 |
|
Use of non approved work tools on Telehandler machines could result in injury or death. Before installing a work tool on this machine, ensure that it is approved by AVSpare and that a AVSpare load chart covering its use is installed in the machine's cab. |
Show/hide table
| NOTICE |
|---|
|
When certain work tools are fitted, the work tools can contact the front tires or the front fenders. This situation can occur when the boom is retracted and the work tool is rotated fully forward. Always check for interference when first operating a new work tool. |
The work tools that are listed in these tables are approved by AVSpare for use on the machines that are covered by this manual. The part number of the work tool is marked on the identification plate for the work tool. Use the following tables to determine that the work tool has been approved by AVSpare. Additional work tools may have been approved since the publication of this manual. You must consult your AVSpare dealer before using any work tool that is not in these tables. All work tools must be used in conjunction with the appropriate load chart. Use the following tables to ensure that you are using the correct load chart. You must know the load carrying capacity of these work tools. Make sure that you are using the correct load chart.
Show/hide table
| TH220B | |
|---|---|
| AVSpare Approved Work Tools(1) | |
| Part Number | Work Tool |
| 229-9714(2) | Material Handling Arm Gp |
| 174-7730 | Carriage (Wide) |
| 174-7728 | Rotating Carriage (Standard) |
| 174-7726 | Rotating Carriage (Wide) |
| 222-6210 | Fork Carriage Ar (Sideshift) |
| 215-4350 | Fork Carriage Gp (Standard) |
| 145-5346 | Fork Gp (Pallet (1220 mm)) |
| 145-5347 | Fork Gp (Block (1220 mm)) |
| 145-5342 | Fork Gp (Pallet 1024 mm) |
| 145-5343 | Fork Gp (Pallet 1220 mm) |
| 145-5345 | Fork Gp (Block (1220 mm)) |
| 215-7964 | Fork Gp (Pallet (1070 mm)) |
| 215-7963 | Fork Gp (Pallet (1525 mm)) |
| 186-5843 | Fork Gp (Manure) |
| 186-5851 | Grapple and Push Off Fork Gp |
| 186-5847 | Grapple Fork Ar |
| 186-6054 | Grapple Fork Gp |
| 163-4263 | Bale Handler Ar |
| 169-3945(3) | Truss Boom Gp |
| 169-6460(4) | Lifting Hook Gp |
| 163-4261 | General Purpose Bucket Ar ( |
| 163-4265 | Multipurpose Bucket Ar ( |
| 186-5838 | Material Handling Bucket Gp ( |
| 219-5515 | Grapple Bucket Ar |
| 220-4759 | Light Material Bucket Gp ( |
| 220-4760 | Light Material Bucket Gp ( |
| 220-4761 | Light Material Bucket Gp ( |
| 190-0913 | Hopper |
| 221-1960 | Pickup Broom Arrangement |
Show/hide table
| (1) | Observe the Local Regulations in certain regions, when you use AVSpare approved work tools. |
| (2) | Changes in Local Regulations prohibit the use of this material handling arm gp in Australia and New Zealand. |
| (3) | Changes in Local Regulations prohibit the use of this boom extension in Australia and New Zealand. |
| (4) | Changes in Local Regulations prohibit the use of this lifting group in Australia and New Zealand. |
Show/hide table
| TH330B | |
|---|---|
| AVSpare Approved Work Tools(1) | |
| Part Number | Work Tool |
| 229-9714(2) | Material Handling Arm Gp |
| 174-7730 | Carriage (Wide) |
| 174-7728 | Rotating Carriage (Standard) |
| 174-7726 | Rotating Carriage (Wide) |
| 222-6210 | Fork Carriage Ar (Sideshift) |
| 215-4350 | Fork Carriage Gp (Standard) |
| 145-5346 | Fork Gp (Pallet (1220 mm)) |
| 145-5347 | Fork Gp (Block (1220 mm)) |
| 145-5342 | Fork Gp (Pallet 1024 mm) |
| 145-5343 | Fork Gp (Pallet 1220 mm) |
| 145-5345 | Fork Gp (Block (1220 mm)) |
| 215-7964 | Fork Gp (Pallet (1070 mm)) |
| 215-7963 | Fork Gp (Pallet (1525 mm)) |
| 186-5843 | Fork Gp (Manure) |
| 186-5851 | Grapple and Push Off Fork Gp |
| 186-5847 | Grapple Fork Ar |
| 186-6054 | Grapple Fork Gp |
| 163-4263 | Bale Handler Ar |
| 169-3945(3) | Truss Boom Gp |
| 169-6460(4) | Lifting Hook Gp |
| 163-4261 | General Purpose Bucket Ar ( |
| 163-4265 | Multipurpose Bucket Ar ( |
| 186-5838 | Material Handling Bucket Gp ( |
| 219-5515 | Grapple Bucket Ar |
| 220-4759 | Light Material Bucket Gp ( |
| 220-4760 | Light Material Bucket Gp ( |
| 220-4761 | Light Material Bucket Gp ( |
| 190-0913 | Hopper |
| 221-1960 | Pickup Broom Arrangement |
Show/hide table
| (1) | Observe the Local Regulations in certain regions, when you use AVSpare approved work tools. |
| (2) | Changes in Local Regulations prohibit the use of this material handling arm gp in Australia and New Zealand. |
| (3) | Changes in Local Regulations prohibit the use of this boom extension in Australia and New Zealand. |
| (4) | Changes in Local Regulations prohibit the use of this lifting group in Australia and New Zealand. |
Show/hide table
| TH340B | |
|---|---|
| AVSpare Approved Work Tools(1) | |
| Part Number | Work Tool |
| 229-9714(2) | Material Handling Arm Gp |
| 174-7730 | Carriage (Wide) |
| 174-7728 | Rotating Carriage (Standard) |
| 174-7726 | Rotating Carriage (Wide) |
| 222-6210 | Fork Carriage Ar (Sideshift) |
| 215-4350 | Fork Carriage Gp (Standard) |
| 145-5346 | Fork Gp (Pallet (1220 mm)) |
| 145-5347 | Fork Gp (Block (1220 mm)) |
| 145-5342 | Fork Gp (Pallet 1024 mm) |
| 145-5343 | Fork Gp (Pallet 1220 mm) |
| 145-5345 | Fork Gp (Block (1220 mm)) |
| 215-7964 | Fork Gp (Pallet (1070 mm)) |
| 215-7963 | Fork Gp (Pallet (1525 mm)) |
| 169-3945(3) | Truss Boom Gp |
| 169-6460(4) | Lifting Hook Gp |
| 163-4261 | General Purpose Bucket Ar ( |
| 163-4265 | Multipurpose Bucket Ar ( |
| 186-5838 | Material Handling Bucket Gp ( |
| 219-5515 | Grapple Bucket Ar |
| 190-0913 | Hopper |
| 221-1960 | Pickup Broom Arrangement |
Show/hide table
| (1) | Observe the Local Regulations in certain regions, when you use AVSpare approved work tools. |
| (2) | Changes in Local Regulations prohibit the use of this material handling arm gp in Australia and New Zealand. |
| (3) | Changes in Local Regulations prohibit the use of this boom extension in Australia and New Zealand. |
| (4) | Changes in Local Regulations prohibit the use of this lifting group in Australia and New Zealand. |
Information System:
D6R Series II Track-Type Tractor
Heating and Air Conditioning Control
TH350B, TH355B, TH360B and TH460B Telehandlers
Lifting Capacities
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train
Modulating Valve (Transmission Clutch) - Install
2003/06/02
New Printer Is Used for Caterpillar Payload Control System (PCS) {749P}
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train
Modulating Valve (Transmission Clutch) - Remove
TH350B, TH355B, TH360B and TH460B Telehandlers
Longitudinal Stability Indicator - Test
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train
Relief Valve (Transmission Hydraulic Control) - Assemble
D6R Series II Track-Type Tractor
Reference Material
D6R Series II Track-Type Tractor
Operation
D5N Track-Type Tractor Power Train
Track Roller Frame - Install
D5N Track-Type Tractor Power Train
Track Roller Frame - Remove
TH220B, TH330B and TH340B Telehandlers
Tire Shipping Pressure
2003/03/10
The Suction Line Filter Group for the Transmission is Relocated {3016, 3067, 3154}
2003/03/10
Explanation of Transmission Oil Temperature Sensors {5574}
980G Series II Wheel Loader Braking System
Hydraulic Oil Contamination - Test
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train
Drive Shaft (Center) - Remove and Install
D6N Track-Type Tractor Machine Systems
Bulldozer Control Valve - Remove
D6N Track-Type Tractor Machine Systems
Bulldozer Control Valve - Install
D5N Track-Type Tractor Power Train
Final Drive - Disassemble
D5N Track-Type Tractor Power Train
Final Drive - Assemble
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Machine Systems
Hydraulic Tank - Remove
938G Series II Wheel Loader and IT38G Series II Integrated Toolcarrier Power Train
Differential and Bevel Gear - Install
D6R Series II Track-Type Tractor
Reference Material
TH210 and TH215 Telehandlers
Daily Inspection