There are several specific warning signs on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all warning signs.
Make sure that all of the warning signs are legible. Clean the warning signs or replace the warning signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the warning signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the warning sign. Loose adhesive will allow the warning sign to fall.
Replace any safety sign that is damaged, or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Any AVSpare dealer can provide new safety signs.
Do Not Operate
 | |
| Illustration 1 | g00111634 |
This warning label is located in the cab under the gauge panel.
 |
| g00111635 |
 |
Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility. |
 |
Enclosed ROPS
 | |
| Illustration 2 | g00118125 |
This warning label is located on the outside of the cab on the left front side.
 |
| g00111632 |
|
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
|
Open ROPS
 | |
| Illustration 3 | g00280313 |
This warning label is located on the rear in the center of the structure.
| |
| g00111632 |
|
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification. |
|
Pressurized System
 | |
| Illustration 4 | g00118126 |
Open the access panel on the top of the hood. The warning label is located on the radiator on the left side of the machine.
 |
| g00102174 |
|
Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure. |
|
Brace Lift Cylinder
 | |
| Illustration 5 | g00274643 |
The warning label is located on the lift arm linkage.
 |
| g00274644 |
|
Unsupported lift arms can fall and cause personal injury. Clamp lift arm support bracket to lift cylinder rod before servicing engine area. Bracket is stored on loader arm cross tube. |
|
High Pressure Cylinder (Cover)
 | |
| Illustration 6 | g00122904 |
This warning label is located on the top of the adjustment valve cover.
 |
| g00122899 |
|
HIGH PRESSURE CYLINDER Do not remove any parts until all pressure has been relieved to avoid possible personal injury. Relieve pressure by opening relief valve one turn maximum. See maintenance guide for track adjustment procedure. TRACK ADJUSTMENT PROCEDURE
|
|
High Pressure Cylinder (Valve)
 | |
| Illustration 7 | g00122908 |
This warning label is located on the top of the track adjustment valve.
 |
| g00122900 |
|
HIGH PRESSURE CYLINDER Do not remove any parts until all pressure has been relieved to avoid possible personal injury. Relieve pressure by opening relief valve one turn maximum. See maintenance guide for track adjustment procedure. TRACK ADJUSTMENT PROCEDURE
|
|
Batteries
 | |
| Illustration 8 | g00122922 |
Open the access door to the battery compartment. The warning label is located on the inside of the access door.
 |
| g00122920 |
|
Improper jumper cable connections can cause explosion resulting in personal injury. Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual. |
|
Battery
 | |
| Illustration 9 | g00122940 |
The warning label is located on the battery.
 |
| g00109769 |
|
DANGER/POISON Shield eyes, Exposive gases. Can cause blindness or injury. No sparks, flames or smoking. Sulfuric Acid can cause blindness or severe burns. FLUSH EYES IMMEDIATELY WITH WATER. Get medical help fast. Keep out of reach of chrildren. Contains sulfuric acid. For medical emergency in USA or Canada contact: 800-458-5924, other countries contact:, 303-893-1322 . |
|
Ether
 | |
| Illustration 10 | g00111633 |
This warning label is located on the air cleaner inside the engine compartment.
 |
| g00103679 |
Do not spray ether into the intake.