D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Warning Signs and Labels Caterpillar


Warning Signs and Labels
`
1.1. Do Not Operate
2.1. ROPS
3.1. Pressurized System
4.1. High Pressure Cylinder (Cover)
5.1. High Pressure Cylinder (Valve)
6.1. Batteries
7.1. Battery
8.1. Ether

There are several specific warning signs on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all warning signs.

Make sure that all of the warning signs are legible. Clean the warning signs or replace the warning signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the warning signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the warning sign. Loose adhesive will allow the warning sign to fall.

Replace any safety sign that is damaged, or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Any AVSpare dealer can provide new safety signs.

Do Not Operate




Illustration 1g00111634

This warning label is located in the cab under the gauge panel.



g00111635

------ WARNING! ------

Do not operate or work on this machine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manuals. Failure to follow the instructions or heed the warnings could result in injury or death. Contact your AVSpare dealer for replacement manuals. Proper care is your responsibility.

----------------------

ROPS




Illustration 2g00118125

This warning label is located on the outside of the cab on the left front side.



g00111632

------ WARNING! ------

Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a AVSpare dealer to determine this structure's limitations without voiding its certification.

----------------------

Pressurized System




Illustration 3g00118126

Open the access panel on the top of the hood. The warning label is located on the radiator on the left side of the machine.



g00102174

------ WARNING! ------

Pressurized system: Hot coolant can cause serious burn. To open cap, stop engine, wait until radiator is cool. Then loosen cap slowly to relieve the pressure.

----------------------

High Pressure Cylinder (Cover)




Illustration 4g00122904

This warning label is located on the top of the adjustment valve cover.



g00122899

------ WARNING! ------

HIGH PRESSURE CYLINDER

Do not remove any parts until all pressure has been relieved to avoid possible personal injury. Relieve pressure by opening relief valve one turn maximum. See maintenance guide for track adjustment procedure.

TRACK ADJUSTMENT PROCEDURE

  1. Adjust idler forward to tight track position.

  1. Open relief valve one turn maximum. Adjust idler back 10 mm (.39 inch). Close relief valve.
----------------------

High Pressure Cylinder (Valve)




Illustration 5g00122908

This warning label is located on the top of the track adjustment valve.



g00122900

------ WARNING! ------

HIGH PRESSURE CYLINDER

Do not remove any parts until all pressure has been relieved to avoid possible personal injury. Relieve pressure by opening relief valve one turn maximum. See maintenance guide for track adjustment procedure.

TRACK ADJUSTMENT PROCEDURE

  1. Adjust idler forward to tight track position.

  1. Open relief valve one turn maximum. Adjust idler back 10 mm (.39 inch). Close relief valve.
----------------------

Batteries




Illustration 6g00122922

Open the access door to the battery compartment. The warning label is located on the inside of the access door.



g00122920

------ WARNING! ------

Improper jumper cable connections can cause explosion resulting in personal injury.

Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual.

----------------------

Battery




Illustration 7g00122940

The warning label is located on the battery.



g00109769

------ WARNING! ------

DANGER/POISON

Shield eyes, Exposive gases. Can cause blindness or injury.

No sparks, flames or smoking.

Sulfuric Acid can cause blindness or severe burns.

FLUSH EYES IMMEDIATELY WITH WATER. Get medical help fast.

Keep out of reach of chrildren. Contains sulfuric acid. For medical emergency in USA or Canada contact: 800-458-5924, other countries contact:, 303-893-1322 .

----------------------

Ether




Illustration 8g00111633

This warning label is located on the air cleaner inside the engine compartment.



g00103679

Do not spray ether into the intake.

Information System:

D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Track Adjustment - Adjust
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Shipping the Machine
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Sampling Interval and Location of Sampling Valve
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Ripping
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Lubricant Viscosities
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Product Identification Number, Serial Number and EU's CE Plate Locations
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Model View Illustrations
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Lifting and Tying Down the Machine
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Land Clearing
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Hydraulic System Oil Filter - Replace
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Hydraulic System Oil - Change
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Gauges
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Heating and Air Conditioning Control - If Equipped
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Air Conditioner - Test
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Braking System - Test
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Bulldozer Blade Lift Control
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Bulldozer Blade Tilt and Angle Control
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Dozing
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Fire Prevention and Explosion Prevention
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Towing the Machine
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Walk-Around Inspection
TH62, TH63, TH82 and TH83 Telehandlers Engine Valve Lash - Check
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Changing Direction and Speed
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Cooling System Coolant (DEAC) - Change