938G Wheel Loader and IT38G Integrated Toolcarrier Transmission Oil Filter - Replace Caterpillar


Transmission Oil Filter - Replace
`
938G Wheel Loader and IT38G Integrated Toolcarrier [SEBU7037]
POWER TRAIN
FILTER GP
938G Wheel Loader and IT38G Integrated Toolcarrier Transmission Oil Filter - Replace


NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products.

Dispose of all fluids according to local regulations and mandates.




Illustration 1g00110529

The transmission oil filter is located on the left side of the machine.



    Illustration 2g00110528

  1. Use a strap type wrench to remove the filter element. Dispose of the used filter element properly.

  2. Clean the filter mounting base. Make sure that all of the used gasket is completely removed.


    Illustration 3g00101318

  3. Apply a light coat of clean transmission oil to the seal of the new filter element. Install a new transmission oil filter hand tight until the seal of the transmission oil filter contacts the base. Note the position of the index marks on the filter in relation to a fixed point on the filter base.

    Note: There are rotation index marks on the transmission oil filter that are spaced 90 degrees or 1/4 or a turn away from each other. When you tighten the transmission oil filter, use the rotation index marks as a guide.

  4. Tighten the filter according to the instructions that are printed on the filter. Use the index marks as a guide. For non-AVSpare filters, use the instructions that are provided with the filter.

    Note: You may need to use a AVSpare strap wrench, or another suitable tool, in order to turn the filter to the amount that is required for final installation. Make sure that the installation tool does not damage the filter.

  5. Start the engine and apply the service brake. Slowly operate the transmission controls in order to circulate the transmission oil.

  6. Move the transmission control to the NEUTRAL position and engage the parking brake. Inspect the transmission oil filter for leaks.

  7. Check the transmission oil level.

    Reference: Refer to Operation and Maintenance Manual, "Transmission Oil Level - Check" for the correct procedure.

Information System:

938G Wheel Loader and IT38G Integrated Toolcarrier Radiator Core - Clean
631E Series II Wheel Tractor-Scrapers Fire Prevention and Explosion Prevention
D11R Track-Type Tractor Engine Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Oil Filter - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier Hydraulic System Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier Fuel Tank Water and Sediment - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier Fuel Tank Cap and Strainer - Clean
631E Series II Wheel Tractor-Scrapers Seat Belt (Retractable)
938G Wheel Loader and IT38G Integrated Toolcarrier Fuel System Primary Filter (Water Separator) Element - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier Fuel System Primary Filter (Water Separator) - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier Fuel System - Prime
938G Wheel Loader and IT38G Integrated Toolcarrier Transmission Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier Traction Control System (TCS) - If Equipped
966G and 972G Wheel Loaders Payload Control System (PCS) - If Equipped
3408C, 3412, 3412C, and 3412D High Performance Marine Engines Engine Air Cleaner Service Indicator - Inspect
938G Wheel Loader and IT38G Integrated Toolcarrier Capacities (Refill)
938G Wheel Loader and IT38G Integrated Toolcarrier Alert Indicators
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Battery Disconnect Switch
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Cab Air Filter - Clean/Replace
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Engine Air Filter Secondary Element - Replace
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Engine Start Switch
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Fuses - Replace
D3C Series III, D4C Series III and D5C Series III HYSTAT Track-Type Tractors Gauges