Engine Oil Level - Check
`
938G Wheel Loader and IT38G Integrated Toolcarrier
[SEBU7037]
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Governor Oil Supply Screen - Clean/Inspect/Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil and Filter - Change
BASIC ENGINE
PAN GP-OIL
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil and Filter - Change
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Do not under fill or overfill engine crankcase with oil. Either condition can cause engine damage. |
Show/hide table
| |
| Illustration 1 | g00110524 |
- Open the engine access door on the right side of the machine. The engine oil dipstick is located on the right side of the machine.
Show/hide table
Illustration 2 g00581153 - While the engine is stopped, maintain the oil level in the crosshatched region of the engine oil dipstick (1).
- If necessary, remove the engine oil filler cap (2) and add oil.
- Clean the engine oil filler cap and install the engine oil filler cap.
- Close the engine access door.
Information System:
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Governor Oil Supply Screen - Clean/Inspect/Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant Extender (ELC) - Add
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant (ELC) - Change
631E Series II Wheel Tractor-Scrapers
General Hazard Information
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Air Filter Secondary Element - Replace
992G Wheel Loader Electrohydraulic System
Implement Electronic Control Pinout Specifications
938G Wheel Loader and IT38G Integrated Toolcarrier
Battery Disconnect Switch
938G Wheel Loader and IT38G Integrated Toolcarrier
Plate Locations and Film Locations
Installation of Retractable Seat Belt{7327}
D7R Track-Type Tractor
Machine Operation Information
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil and Filter - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuses - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System - Prime
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) Element - Replace
631E Series II Wheel Tractor-Scrapers
Seat Belt (Retractable)
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Cap and Strainer - Clean
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Water and Sediment - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil Filter - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil Level - Check
D11R Track-Type Tractor
Engine Oil Level - Check