Engine Governor Oil Supply Screen - Clean/Inspect/Replace
`
938G Wheel Loader and IT38G Integrated Toolcarrier
[SEBU7037]
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil Level - Check
FUEL SYSTEM
GOVERNOR GP
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Governor Oil Supply Screen - Clean/Inspect/Replace
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in AVSpare machines. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
 | |
| Illustration 1 | g00111718 |
Open the engine hood. The engine governor is on the right side of the machine.
Show/hide table
 | |
| Illustration 2 | g00111733 |
- Remove the governor oil supply tube (1) from the governor.
- Remove the fitting (2) from the governor housing and remove the seal (3) from the governor housing.
- Remove the screen (4) with a 6 mm hexagon wrench.
- Wash the screen in solvent in order to remove any debris. Inspect the screen for damage. Inspect the seals for damage. Replace the screen and/or the seals, if necessary.
- Install the screen far enough into the governor housing in order to allow clearance for the seals and for the fitting.
- Install the seal, the fitting, and the governor oil supply tube. Close the engine hood.
Information System:
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant Extender (ELC) - Add
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant (ELC) - Change
631E Series II Wheel Tractor-Scrapers
General Hazard Information
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Air Filter Secondary Element - Replace
992G Wheel Loader Electrohydraulic System
Implement Electronic Control Pinout Specifications
938G Wheel Loader and IT38G Integrated Toolcarrier
Battery Disconnect Switch
938G Wheel Loader and IT38G Integrated Toolcarrier
Plate Locations and Film Locations
Installation of Retractable Seat Belt{7327}
D7R Track-Type Tractor
Machine Operation Information
D7R Track-Type Tractor
Refill Capacities
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil and Filter - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuses - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System - Prime
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) Element - Replace
631E Series II Wheel Tractor-Scrapers
Seat Belt (Retractable)
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Cap and Strainer - Clean
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Water and Sediment - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil Filter - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil Level - Check