Differential and Final Drive Oil Level - Check
`
938G Wheel Loader and IT38G Integrated Toolcarrier
[SEBU7037]
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Governor Oil Supply Screen - Clean/Inspect/Replace
POWER TRAIN
AXLE GP
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Braking System - Test
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
- Operate the machine for a few minutes. This will allow all of the oil to reach a common level.
- Park the machine on level ground. Lower the attachment and apply slight downward pressure. Engage the parking brake. Stop the machine.
Show/hide table
Illustration 1 g00277215 Front Differential and Final Drive Filler Plug Show/hide table
Illustration 2 g00110469 Rear Differential and Final Drive Filler Plug - Remove the dipstick/fill plug for the differential. Wipe off the dipstick and reinstall the dipstick/fill plug completely. This will ensure a more accurate measurement.
- Remove the dipstick/fill plug for the differential again. Check the oil level. Maintain the oil level between the "ADD" mark and the "FULL" mark. Add oil, if necessary.
- Install the dipstick/fill plug.
Information System:
938G Wheel Loader and IT38G Integrated Toolcarrier
Differential and Final Drive Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant Extender (ELC) - Add
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Coolant (ELC) - Change
631E Series II Wheel Tractor-Scrapers
General Hazard Information
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Air Filter Secondary Element - Replace
992G Wheel Loader Electrohydraulic System
Implement Electronic Control Pinout Specifications
938G Wheel Loader and IT38G Integrated Toolcarrier
Battery Disconnect Switch
938G Wheel Loader and IT38G Integrated Toolcarrier
Plate Locations and Film Locations
Installation of Retractable Seat Belt{7327}
D7R Track-Type Tractor
Machine Operation Information
D7R Track-Type Tractor
Refill Capacities
938G Wheel Loader and IT38G Integrated Toolcarrier
Cooling System Water Temperature Regulator - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Governor Oil Supply Screen - Clean/Inspect/Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil Level - Check
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Oil and Filter - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuses - Replace
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System - Prime
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel System Primary Filter (Water Separator) Element - Replace
631E Series II Wheel Tractor-Scrapers
Seat Belt (Retractable)
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Cap and Strainer - Clean
938G Wheel Loader and IT38G Integrated Toolcarrier
Fuel Tank Water and Sediment - Drain
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil - Change
938G Wheel Loader and IT38G Integrated Toolcarrier
Hydraulic System Oil Filter - Replace