D7R Track-Type Tractor Braking System - Test Caterpillar


Braking System - Test
`
D7R Track-Type Tractor [SEBU6896]
STEERING AND BRAKING SYSTEM
BRAKE GP
D7R Track-Type Tractor Brakes, Indicators and Gauges - Test
D7R Track-Type Tractor Braking System - Test

------ WARNING! ------

If the machine moves during the test, reduce the engine speed immediately, and engage the parking brake.

If the machine moved while testing the brakes, consult your AVSpare dealer for brake inspection and repair. Damaged brakes must be repaired before returning the machine to operation.

----------------------

Make sure that the area around the machine is clear of personnel and clear of obstacles.

Test the brakes on a dry, level surface.

Fasten the seat belt before you test the brakes.

The following test is used to determine whether the service brake is functional. This test is not intended to determine the maximum brake holding effort. The brake holding effort of this machine will be different from the brake holding effort of other machines because of the variations in the engine setting, in the power train efficiency, and in the brake holding ability.

Compare the engine speed at the beginning of machine movement to the engine speed of a prior test. This will be an indication of the amount of system deterioration.

  1. Start the engine.

  1. Raise all attachments.

  1. Depress the brake pedal.

  1. Select the mode of manual shift.

  1. Release the parking brake.

  1. While the brake pedal is depressed, move the directional control to the NEUTRAL position.

  1. Select the THIRD SPEED position. The control panel will indicate "3N" .

    Note: When you test the brake system, make sure that the transmission is in the THIRD SPEED position. You can depress the button in order to read the speed on the digital display window.

  1. Select the FORWARD position. The control panel will indicate "3F" .

  1. Gradually increase the engine speed to full load speed. The machine should not move.

  1. Move the directional control to the NEUTRAL position.

  1. Move the throttle switch to LOW IDLE. Turn on the parking brake switch. Lower all attachments to the ground. Apply a slight down pressure. Stop the engine.


NOTICE

If the machine moved while testing the brakes, contact your AVSpare dealer. Have the dealer inspect and, if necessary, repair the service brake before returning the machine to operation.


Information System:

IT28G Integrated Toolcarrier and 928G Wheel Loader Axle Housing and Bearing Preload Adjustment
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Capacities (Refill)
D7R Track-Type Tractor Sound Information and Vibration Information
IT28G Integrated Toolcarrier and 928G Wheel Loader Limited Slip Differential
IT28G Integrated Toolcarrier and 928G Wheel Loader Differential Backlash and Bearing Adjustment
992G Wheel Loader and 854G Wheel Dozer Power Train Transmission Planetary
IT28G Integrated Toolcarrier and 928G Wheel Loader Differential Pinion Preload Adjustment
D7R Track-Type Tractor Model View Illustrations
IT28G Integrated Toolcarrier and 928G Wheel Loader Brake and Planetary
D7R Track-Type Tractor Lifting and Tying Down the Machine
Installing Maintenance Free Linkage Seals{6107}
IT28G Integrated Toolcarrier and 928G Wheel Loader Axle (Oscillating)
938G Wheel Loader and IT38G Integrated Toolcarrier Cooling System Water Temperature Regulator - Replace
D7R Track-Type Tractor Refill Capacities
D7R Track-Type Tractor Machine Operation Information
Installation of Retractable Seat Belt{7327}
938G Wheel Loader and IT38G Integrated Toolcarrier Plate Locations and Film Locations
938G Wheel Loader and IT38G Integrated Toolcarrier Battery Disconnect Switch
992G Wheel Loader Electrohydraulic System Implement Electronic Control Pinout Specifications
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Air Filter Secondary Element - Replace
631E Series II Wheel Tractor-Scrapers General Hazard Information
938G Wheel Loader and IT38G Integrated Toolcarrier Cooling System Coolant (ELC) - Change
938G Wheel Loader and IT38G Integrated Toolcarrier Cooling System Coolant Extender (ELC) - Add
938G Wheel Loader and IT38G Integrated Toolcarrier Differential and Final Drive Oil - Change