Starting with Auxiliary Start Receptacle
`
D6R Track-Type Tractor
[SEBU6887]
D6R Track-Type Tractor
Plate Locations and Film Locations
D6R Track-Type Tractor
Equalizer Bar Pins - Lubricate
ELECTRICAL AND STARTING SYSTEM
WIRING GP
D6R Track-Type Tractor
Starting with Auxiliary Start Receptacle
D6R Track-Type Tractor
Fuses - Replace
Show/hide table
Illustration 1 | g00103715 |
The auxiliary start receptacle is on the right side of the machine.
Some AVSpare products may be equipped with auxiliary start receptacles. All other machines can be equipped with a receptacle for parts service. A permanent receptacle is always available for jump starting.
There are two cable assemblies that can be used to jump the stalled machine. You can jump the machine from another machine that is equipped with this receptacle or an auxiliary power pack. Your AVSpare dealer can provide the correct cable lengths for your application.
- Determine the failure of the machine to start. Refer to Special Instructions, SEHS7768 on the use of 6V-2150 Starting Charging Analyzer Group .
- Place the transmission control in the NEUTRAL position on the stalled machine. Engage the parking brake. Lower all implements to the ground. Move all controls to the HOLD position.
- On the stalled machine, turn the start switch key to the OFF position. Turn all of the accessories to the OFF position.
- Turn the battery disconnect switch ON .
- Move the machine that is used for the electrical source close to the stalled machine. The cables must reach. DO NOT ALLOW THE MACHINES TO CONTACT EACH OTHER.
- Stop the engine on the machine that is used for the electrical source. When you use an auxiliary power source, turn the charging system to the OFF position.
- On the stalled machine, connect the appropriate jump start cable to the auxiliary start receptacle.
- Connect the other end of this cable to the electrical source. You must connect the cable to the auxiliary start receptacle.
- Start the engine on the machine that is used for the electrical source. Also, you can energize the charging system on the auxiliary power source.
- Allow the electrical source to charge the batteries for two minutes.
- Attempt to start the stalled engine. Refer to Operation and Maintenance Manual, "Engine Starting". See the beginning of this topic.
- Immediately after the stalled engine starts, disconnect the jump start cable from the electrical source.
- Disconnect the other end of this cable from the stalled machine.
- Conclude with a failure analysis on the starting charging system. Check the stalled machine, as required. Check the machine when the engine is running and the charging system is in operation.
Information System:
D7R Track-Type Tractor
Brakes, Indicators and Gauges - Test
D6R Track-Type Tractor
Plate Locations and Film Locations
D6R Track-Type Tractor
Sound Information and Vibration Information
561M Pipelayer
Cooling System Additive (DEAC) - Add
D7R Track-Type Tractor
Warning Signs and Labels
D6R Track-Type Tractor
Model View Illustrations
D6R Track-Type Tractor
Refill Capacities
631E Series II Wheel Tractor-Scrapers
Tire Inflation with Nitrogen
D6R Track-Type Tractor
Lifting and Tying Down the Machine
D6R Track-Type Tractor
Cooling System Level - Check
D6R Track-Type Tractor
Bulldozer Blade Tilt
D7R Track-Type Tractor
After Starting Engine
D6R Track-Type Tractor
Equalizer Bar Pins - Lubricate
D6R Track-Type Tractor
Engine Air Filter Primary Element - Clean/Replace
992G Wheel Loader Electrohydraulic System
Linkage Pin and Seal Group (Bucket Control)
C12 Marine Engines and C12 Power Package
Cooling System Coolant (ELC) - Change
D6R Track-Type Tractor
Engine Air Filter Secondary Element - Replace
D6R Track-Type Tractor
Machine Operation Information
D6R Track-Type Tractor
Parking Brake Control
D6R Track-Type Tractor
Engine Oil Level - Check
561M Pipelayer
Seat Adjustment
D6F SR, D6G and D6G SR Track-Type Tractors
Operation
D6R Track-Type Tractor
Fuses - Replace
D6M Track-Type Tractor
Towing the Machine