Transmission Oil - Change
`
928G Wheel Loader
[SEBU7015]
POWER TRAIN
FILLER GP-POWER TRAIN OIL
928G Wheel Loader
Transmission Oil - Change
Operate the machine for a few minutes in order to warm the transmission oil.
The machine should be level. Lower the bucket to the ground and apply slight downward pressure. Engage the parking brake and stop the engine.
Show/hide table
![]() | |
Illustration 1 | g00461437 |
- Remove the cover on the guard (if equipped).
- Remove the transmission drain plug. Allow the transmission oil to drain into a suitable container. Clean the transmission drain plug and install the transmission drain plug.
Show/hide table
![]() | |
Illustration 2 | g00101961 |
- Change the transmission oil filter element. Refer to Operation and Maintenance Manual, "Transmission Oil Filter - Replace".
- Clean the transmission magnetic screen. Refer to Operation and Maintenance Manual, "Transmission Magnetic Screen - Clean".
- Fill the transmission with transmission oil through the transmission filler tube. Refer to Operation and Maintenance Manual, "Lubricant Viscosities" and Operation and Maintenance Manual, "Refill Capacities".
Show/hide table
![]() | |
Illustration 3 | g00101962 |
- Remove the transmission breather that is located on the top of the transmission case. Install a new transmission breather.
Show/hide table
![]() | |
Illustration 4 | g00101963 |
- Start the engine and run the engine at low idle. Apply the service brake. Slowly operate the transmission controls in order to circulate the oil.
- Move the transmission control lever to NEUTRAL and engage the parking brake. Inspect the transmission for leaks.
- Maintain the transmission oil level between the "LOW" mark and the "HIGH" mark in the sight gauge when the transmission is warm and the engine is running. Maintain the transmission oil level to the top of the sight gauge when the transmission is cool and the engine is not running. Add transmission oil through the transmission filler tube, if necessary.
Show/hide table
![]() | |
Illustration 5 | g00101964 |
- Stop the engine.
Information System:
561M Pipelayer
Cooling System Coolant (DEAC) - Change
D6M Track-Type Tractor
Engine Oil and Filter - Change
928G Wheel Loader
Radiator Core - Clean
D6M Track-Type Tractor
Refill Capacities
928G Wheel Loader
Hydraulic System Oil Level - Check
928G Wheel Loader
Hydraulic System Oil Filter - Replace
928G Wheel Loader
Hydraulic System Oil - Change
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuel System - Prime
D6M Track-Type Tractor
Bulldozer Blade Tilt
928G Wheel Loader
Fuel System Water Separator Element - Replace
928G Wheel Loader
Fuel System Primary Filter - Replace
515 Wheel Skidder and 525 Wheel Skidder
Machine Retrieval
928G Wheel Loader
Transmission Oil Filter - Replace
928G Wheel Loader
Walk-Around Inspection
561M Pipelayer
Bevel and Transfer Gears - Power Shift
Installation of Output Yoke and Screen Housing On Remanufactured Transmissions{3002, 3159}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Transmission Oil - Change
992G Wheel Loader and 854G Wheel Dozer Steering System
Piston Pump (Steering)
D6M Track-Type Tractor
Fuel System Primary Filter - Clean/Replace
631E Series II Wheel Tractor-Scrapers
Lubricant Information
D6M Track-Type Tractor Power Train
Steering and Brake Control Valve
D6M Track-Type Tractor
Transmission Oil - Change
631E Series II Wheel Tractor-Scrapers
Engine Oil - Cat Machine Diesel Engines
631E Series II Wheel Tractor-Scrapers
Hydraulic Oil