Engine and Machine Warm-Up
`
651E Wheel Tractor-Scraper
[SEBU6963]
651E Wheel Tractor-Scraper
Engine Starting with Auxiliary Start Receptacle
651E Wheel Tractor-Scraper
Operation Information
ENGINE ARRANGEMENT
651E Wheel Tractor-Scraper
Engine Starting without Starting Aid
651E Wheel Tractor-Scraper
Engine Starting with Ether Starting Aid
627F Wheel Tractor-Scraper
Engine Starting with Jump Start Cables
651E Wheel Tractor-Scraper
Engine Starting with Auxiliary Start Receptacle
651E Wheel Tractor-Scraper
Engine and Machine Warm-Up
651E Wheel Tractor-Scraper
Engine Oil Level - Check
Show/hide table
| NOTICE |
|---|
Keep engine speed low until the engine oil pressure registers on the gauge or the engine oil pressure indicator light goes out. If it does not register or the light does not go out within ten seconds, stop the engine and investigate the cause before starting again. Failure to do so, can cause engine damage. |
Show/hide table
 | |
| Illustration 1 | g00879920 |
- When the engine is cold, operate the engine at low idle for at least five minutes. Engage the attachment controls and disengage the attachment controls. This will help to warm up the hydraulic components.
Cycle all controls in order to allow warm oil to circulate through all hydraulic cylinders and through all hydraulic lines.
While you idle the engine for warm-up, observe the following recommendations:
- If the temperature is greater than 0°C (32°F), warm up the engine for approximately 15 minutes.
- If the temperature is less than 0°C (32°F), warm up the engine for approximately 30 minutes.
- If the temperature is less than - 18°C (0°F) or if hydraulic functions are sluggish, additional time may be required.
- If the temperature is greater than 0°C (32°F), warm up the engine for approximately 15 minutes.
- Move the panel test switch for the electronic monitoring system (EMS) upward. The action alarm should sound. The alert indicators should come on. The action light should flash.
- Release the panel test switch. All alert indicators and the action light should turn off. The action alarm should also turn off. If the alert indicators and the action light does not turn off, stop the engine. Make sure that all necessary repairs are performed before you restart the machine.
- During machine operation, frequently look at the alert indicators and the gauges.
- Check the hydraulic oil level and the transmission oil level. Maintain the oil levels to the "FULL" mark.
Information System:
651E Wheel Tractor-Scraper
Engine Starting with Auxiliary Start Receptacle
627F Wheel Tractor-Scraper
Engine Starting with Jump Start Cables
651E Wheel Tractor-Scraper
Engine Starting with Ether Starting Aid
651E Wheel Tractor-Scraper
Engine Starting without Starting Aid
651E Wheel Tractor-Scraper
Ejector Control
966G and 972G Wheel Loaders
Secondary Steering - If Equipped
561M Pipelayer
Transmission Selector and Pressure Control Valve - Power Shift
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuel System Primary Filter (Water Separator) Element - Replace
928G Wheel Loader
Autoshift Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Oil and Filter - Change
631E Series II Wheel Tractor-Scrapers
Seat Belt
966G and 972G Wheel Loaders
Hydraulic System Oil - Change
651E Wheel Tractor-Scraper
Operation Information
928G Wheel Loader
Bucket Lift Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Air Filter Secondary Element - Replace
D6R Track-Type Tractor
Braking System - Test
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Work Tool Positioner
627F Wheel Tractor-Scraper
General Hazard Information
992G Wheel Loader Electrohydraulic System
Solenoid Valve (Ride Control)
928G Wheel Loader
Multipurpose Control
928G Wheel Loader
Refill Capacities
928G Wheel Loader
V-Belts - Inspect/Adjust/Replace
651E Wheel Tractor-Scraper
Loading
561M Pipelayer
Transmission - Power Shift