Hydraulic System Oil Filter - Replace
`
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
[SEBU7018]
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Transmission Oil Filter - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Oil and Filter - Change
HYDRAULIC SYSTEM
FILTER GP
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Hydraulic System Oil Filter - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Hydraulic System Biodegradable Oil Filter Element - Replace - If Equipped
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "AVSpare Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on AVSpare products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
![]() | |
Illustration 1 | g00765498 |
The hydraulic filter is located on the right side of the machine.
- Use a strap type wrench to remove the filter element. Dispose of the used filter element properly.
- Clean the filter mounting base. Make sure that all of the used gasket is completely removed.
Show/hide table
Illustration 2 g00101318 - Lubricate the gasket of the new filter element with clean hydraulic oil.
- Install the new filter element by hand. After the gasket contacts the filter mounting base, tighten the filter element by an additional 3/4 turn.
- Start the engine and run the engine at low idle. Inspect the hydraulic system for leaks.
Show/hide table
Illustration 3 g00765515 - Maintain the oil level above the “ADD COLD” mark on the sight gauge. Add hydraulic oil, if necessary.
Information System:
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Transmission Oil Filter - Replace
651E Wheel Tractor-Scraper
Directional Turn Signal and Hazard Flasher Control
928G Wheel Loader
Towing the Machine
928G Wheel Loader
Lifting and Tying Down the Machine
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Circuit Breakers - Reset
928G Wheel Loader
Shipping the Machine
D6M Track-Type Tractor
Transmission Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuses - Replace
D6M Track-Type Tractor
Engine Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Specifications
928G Wheel Loader
Bulldozing and Dumping
854G Wheel Dozer Hydraulic System
Hydraulic Tank (Steering, Brake)
651E Wheel Tractor-Scraper
Heating and Air Conditioning Control
966G and 972G Wheel Loaders
Hydraulic System Oil - Change
631E Series II Wheel Tractor-Scrapers
Seat Belt
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Oil and Filter - Change
928G Wheel Loader
Autoshift Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuel System Primary Filter (Water Separator) Element - Replace
561M Pipelayer
Transmission Selector and Pressure Control Valve - Power Shift
966G and 972G Wheel Loaders
Secondary Steering - If Equipped
651E Wheel Tractor-Scraper
Ejector Control
651E Wheel Tractor-Scraper
Engine Starting without Starting Aid
651E Wheel Tractor-Scraper
Engine Starting with Ether Starting Aid
627F Wheel Tractor-Scraper
Engine Starting with Jump Start Cables