Shipping the Machine
`
928G Wheel Loader
[SEBU7015]
MACHINE ARRANGEMENT
Investigate the travel route for overpass clearances. Make sure that there will be adequate clearance if the machine that is transported is equipped with a ROPS, with a cab, or with a canopy.
Before loading, remove ice, snow, or other slippery material from the loading dock and from the truck bed. This is done in order to prevent slippage of the machine. This should also be done in order to prevent a shift while the machine is moving in transit.
Show/hide table
NOTICE |
---|
Obey all state and local laws governing the weight, width and length of a load. Make sure the cooling system has proper antifreeze if moving machine to a colder climate. Observe all regulations governing wide loads. |
- Chock the trailer or rail car wheels before you load the machine. (The trailer is shown.)
Show/hide table
![]() | |
Illustration 1 | g00040011 |
- After the machine is positioned, connect the steering frame lock link in order to hold the front frame and the rear frame in place.
- Lower the attachment to the floor of the transport vehicle. Move the transmission control lever to NEUTRAL.
- Engage the parking brake.
- Turn the engine start switch key to OFF in order to stop the engine. Remove the engine start switch key.
- Move all of the hydraulic control levers in order to relieve any trapped pressure.
- Move the control for the hydraulic lever lock to the LOCKED position.
Show/hide table
![]() | |
Illustration 2 | g00447760 |
- Turn the battery disconnect switch key to OFF and remove the battery disconnect switch key.
- Lock the door and the access covers and attach any vandalism protection.
- Secure the machine with tie-downs when you are transporting the machine on a rail car or on the tractor-trailer.
- Cover the exhaust opening. The turbocharger should not rotate when the engine is not operating. Damage to the turbocharger can result.
Information System:
D6M Track-Type Tractor
Transmission Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuses - Replace
D6M Track-Type Tractor
Engine Oil Level - Check
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Specifications
928G Wheel Loader
Bulldozing and Dumping
854G Wheel Dozer Hydraulic System
Hydraulic Tank (Steering, Brake)
928G Wheel Loader
Secondary Steering
938G Wheel Loader and IT38G Integrated Toolcarrier
Engine Starting with Auxiliary Start Receptacle - If Equipped
D6M Track-Type Tractor
Walk-Around Inspection
992G Wheel Loader Electrohydraulic System
Pressure Sensor (Implement Pilot Oil)
554 Forwarder and 574 Forwarder
Engine Starting with Jump Start Cables
D6M Track-Type Tractor
Fuses - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Circuit Breakers - Reset
928G Wheel Loader
Lifting and Tying Down the Machine
928G Wheel Loader
Towing the Machine
651E Wheel Tractor-Scraper
Directional Turn Signal and Hazard Flasher Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Transmission Oil Filter - Replace
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Hydraulic System Oil Filter - Replace
651E Wheel Tractor-Scraper
Heating and Air Conditioning Control
966G and 972G Wheel Loaders
Hydraulic System Oil - Change
631E Series II Wheel Tractor-Scrapers
Seat Belt
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Engine Oil and Filter - Change
928G Wheel Loader
Autoshift Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders
Fuel System Primary Filter (Water Separator) Element - Replace