834B and 836 Landfill Compactor Safety Signs and Labels Caterpillar


Safety Signs and Labels
`
834B and 836 Landfill Compactor [SEBU6696]
1.1. Do Not Operate
2.1. Do Not Weld On The ROPS
3.1. No Clearance
4.1. Improper Connections Of The Jump Start Cable
5.1. Do Not Step On Cleaner Bar
6.1. Electrical Shock Hazard

There are several specific safety signs on this machine. The exact location of the hazards and the description of the hazards are reviewed in this section. Please become familiarized with all safety signs.

Make sure that all of the safety signs are legible. Clean the safety signs or replace the safety signs if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the safety signs, use a cloth, water and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the safety signs. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the safety sign. Loose adhesive will allow the safety sign to fall.

Replace any safety sign that is damaged or missing. If a safety sign is attached to a part that is replaced, install a safety sign on the replacement part. Any AVSpare dealer can provide new safety signs.

Do Not Operate




Illustration 1g00038379

This warning is located in the cab.



g00038370

------ WARNING! ------

DO NOT OPERATE OR WORK ON THIS MACHINE UNLESS YOU HAVE READ AND UNDERSTAND THE INSTRUCTIONS AND WARNINGS IN THE OPERATION AND MAINTENANCE MANUALS. FAILURE TO FOLLOW THE INSTRUCTIONS OR HEED THE WARNINGS COULD RESULT IN INJURY OR DEATH. CONTACT ANY AVSpare DEALER FOR REPLACEMENT MANUALS. PROPER CARE IS YOUR RESPONSIBILITY.

----------------------

Do Not Weld On The ROPS




Illustration 2g00038780

This warning is located on the ROPS.



g00038778

------ WARNING! ------

Personal injury or death can result when voiding this certification.

Structural damage, an overturn, modification, alteration, or improper repair can impair the ROPS structure's protection capability thereby voiding this certification.

Do not weld on or drill holes in the structure.

To avoid possible weakening of this ROPS, consult a AVSpare dealer before altering this ROPS in any way. The protection offered by this ROPS will be impaired if it has been subjected to structural damage.

Consult a AVSpare dealer to determine this structure's limitations without voiding its certification.

----------------------

"Rollover Protective Structure Certification (ROPS) and Falling Object Protective Structure (FOPS) Certification "

"This structure, when properly installed on a machine which is not altered to exceed the certification test mass meets, at the time of installation, criteria established by: SAE J394, SAE J1040 APR88, ISO 3471-1:1986, ISO 3471:1994, SAE J231 JAN 81, ISO 3449:1992 LEVEL II."

No Clearance




Illustration 3g00038792

This warning is located on the machine on both sides of the articulation hitch.



g00038790

------ WARNING! ------

No clearance for person in this area when machine turns. Severe injury or death from crushing could occur.

----------------------

Connect the steering frame lock between the front and the rear frame. Connect the steering frame lock before lifting. Connect the steering frame lock before transporting. Connect the steering frame lock before the machine is serviced near the articulation pivot.

Disconnect steering frame lock and secure the steering frame lock before resuming operation.

Improper Connections Of The Jump Start Cable




Illustration 4g00038788

This warning is located in the battery compartment.



g00038786

------ WARNING! ------

Improper jumper cable connections can cause an explosion resulting in personal injury. Batteries can be located in separate compartments. When using jumper cable always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal. (If not equipped with starter negative terminal, connect to engine block.)

----------------------

Do Not Step On Cleaner Bar




Illustration 5g00038784

This warning is located on the frame near the cleaner bar.



g00039407

------ WARNING! ------

Do not step on cleaner bar when machine is moving

----------------------

Electrical Shock Hazard




Illustration 6g00039224

This warning is located on the engine valve cover.



g00039226

------ WARNING! ------

Electrical shock hazard. Unit injector system. 90-120 volts

----------------------

Information System:

615C Series II Wheel Tractor-Scraper Hydraulic System Elevator Speed Reducer
615C Series II Wheel Tractor-Scraper Hydraulic System Elevator Frame
611 Wheel Tractor-Scraper Hydraulic System Piston Pump (Axle Suspension)
611 and 615C Series II Wheel Tractor-Scrapers Steering System Steering Control Valve
Installation Of 3Y6693 Regulator Used With 3Y6880 Conversion Kit{1400}
PRODUCT SUPPORT PROGRAM FOR INSPECTING AND INSTALLING THE 4N8150 SPRING AND 3929208 PLUNGER IN THE ENGINE OIL FILTER BASE 4734860 ON CERTAIN AD30 UNDERGROUND ARTICULATED TRUCKS
PRODUCT IMPROVEMENT PROGRAM FOR APPLYING THE PROPER TIGHTENING TO THE MOUNTING BOLTS FOR THE HYSTAT MOTORS ON CERTAIN 926M, 930M, AND 938M SMALL WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRIMARY AND SECONDARY ENGINE FILTER ELEMENTS ON CERTAIN MD6250 ROTARY BLASTHOLE DRILLS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE ENGINE BLOCK FOR COOLANT LEAKS ON CERTAIN 415, 416, 420, 428, 430, 432, 434, AND 444 BACKHOE LOADERS, 910, 914, AND 920 COMPACT WHEEL LOADERS, D1, D2, AND D3 TRACK-TYPE TRACTORS, 313, 315, AND 317 EXCAVA
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE 5117975 FUEL PUMP ON CERTAIN C9.3 REMAN 20R4509, 20R5307, 20R6190, AND 20R6192 LONG BLOCKS, 20R7002, AND 20R7003 REMAN ENGINES IN DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM INSPECTING AND POSSIBLY REWORKING CERTAIN 20R6551 C15 REMAN ENGINES IN DEALER PART STOCK
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING CERTAIN 9U-7763 PULLER STUDS FROM DEALER TOOL INVENTORY AND CUSTOMER TOOL INVENTORY, AND DEALER AND CUSTOMER SERVICE FACILITIES
515 Wheel Skidder and 525 Wheel Skidder General Hazard Information
834B and 836 Landfill Compactor Model View Illustrations
834B and 836 Landfill Compactor Product Identification Number, Serial Number and EU's CE Plate Locations
834B and 836 Landfill Compactor Electronic Monitoring System (EMS)
834B and 836 Landfill Compactor Gauges
834B and 836 Landfill Compactor Parking Brake Manual Release
966G and 972G Wheel Loaders Tire Inflation with Nitrogen
834B and 836 Landfill Compactor Light Switches
834B and 836 Landfill Compactor Backup Alarm
834B and 836 Landfill Compactor Heating and Air Conditioning Control
834B and 836 Landfill Compactor Parking Brake Control
834B and 836 Landfill Compactor Transmission Direction and Speed Control