Every 250 Service Hours Or Monthly
`
992 WHEEL LOADER
[GEG02124]
992 WHEEL LOADER
Fuel And Lubricant Specifications
992 WHEEL LOADER
Every 500 Service Hours Or 3 Months
MACHINE ARRANGEMENT
992 WHEEL LOADER
Safety
992 WHEEL LOADER
Maintenance Recommendations
992 WHEEL LOADER
Fuel And Lubricant Specifications
992 WHEEL LOADER
Every 250 Service Hours Or Monthly
992 WHEEL LOADER
Every 500 Service Hours Or 3 Months
1.1. (9)Engine Crankcase
2.1. (10)Drive Shaft Splines
3.1. (11)Steering Cylinders
4.1. (12)Bucket Control
5.1. (13)Lift Arm
6.1. (14)Alternator Belt
7.1. (15)Air Conditioner Pump Belts
(9)Engine Crankcase
Machine level, bucket lowered, parking brake set and engine stopped.
- 1. Remove crankcase drain valve plug, and open valve and allow to drain.
- 2. Remove oil cooler drain plug and allow to drain.
- 3. Remove filter housing drain plugs and allow to drain.
- 4. Loosen cover bolts and remove housing and filters.
- 5. Clean covers and inspect seals. Use new ones if necessary.
- 6. Clean housings and install housings and new elements. Clean and install drain plugs.
- 7. Close crankcase drain valve.
- 8. Clean and install drain valve plug.
- 9. Clean and install oil cooler drain plug.
- 10. Fill crankcase (refer to Refill Capacities).
- 11. Start engine and allow oil to warm.
- 12. Check oil level.
- 13. Add oil as required to bring level to FULL mark on ENGINE RUNNING side of gauge.
(10)Drive Shaft Splines
- 1. Loader must be fully articulated left or right before lubrication. Stop engine and remove key. Relieve hydraulic pressure. Lubricate 1 fitting in front shaft.
- 2. Lubricate 1 fitting in rear shaft. Fitting is located behind universal joint.
(11)Steering Cylinders
- 1. Lubricate 1 fitting in eye of each cylinder rod.
- 2. Lubricate 1 fitting at head end of each cylinder.
(12)Bucket Control
Lubricate linkage and cylinders. 8 fittings each side.
(13)Lift Arm
Lubricate lift arm linkage and head end of cylinder. 4 fittings each side.
(14)Alternator Belt
- 1. Check condition and adjustment of belt.
- 2. Correct adjustment allows 9/16 to 13/16 inch (14 to 20 mm) deflection. Loosen adjusting locknut.
- 3. Turn adjusting nut to obtain correct adjustment.
- 4. Tighten locknut and recheck adjustment.
(15)Air Conditioner Pump Belts
- 1. Check condition and adjustment of belts.
- 2. Deflection should be 9/16to 13/16 inch (14 to 20 mm) Loosen mounting bolts.
- 3. Loosen adjustment locknut.
- 4. Turn adjusting screw to obtain correct adjustment.
- 5. Tighten locknut.
- 6. Tighten mounting bolts.
- 7. Recheck adjustment.
Information System:
992 WHEEL LOADER
Fuel And Lubricant Specifications
992 WHEEL LOADER
Maintenance Recommendations
992 WHEEL LOADER
Safety
J621 TRACTOR-SCRAPER
When Required
J621 TRACTOR-SCRAPER
Every 2000 Service Hours or 1 Year
J621 TRACTOR-SCRAPER
Every 1000 Service Hours or 6 Months
J621 TRACTOR-SCRAPER
Every 500 Service Hours Or 3 Months
J621 TRACTOR-SCRAPER
Every 250 Service Hours Or Monthly
J621 TRACTOR-SCRAPER
Every 10 Service Hours Or Daily
621 TRACTOR-SCRAPER
Transporting Hints
621 TRACTOR-SCRAPER
Operating Techniques
621 TRACTOR-SCRAPER
Parking The Tractor-Scraper
992 WHEEL LOADER
Every 500 Service Hours Or 3 Months
992 WHEEL LOADER
Every 1000 Service Hours Or 6 Months
992 WHEEL LOADER
Every 2000 Service Hours Or 1 Year
992 WHEEL LOADER
When Required
992 WHEEL LOADER
Beadless Tire Maintenance
992 WHEEL LOADER
Maximum Deformation Of Molded Rib
983 TRAXCAVATOR
Safety
983 TRAXCAVATOR
Fuel And Lubricant Specifications
983 TRAXCAVATOR
Every 250 Service Hours Or Monthly
983 TRAXCAVATOR
Every 1000 Service Hours Or 6 Months
983 TRAXCAVATOR
Every 2000 Service Hours Or 1 Year
983 TRAXCAVATOR
When Required