There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Become familiarized with all messages.
Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.
Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any AVSpare dealer can provide new messages.
| |
| Illustration 1 | g01974238 |
| |
| Illustration 2 | g03643196 |
Engine Coolant Fast Fill (1). This message is located at the front of the radiator on the right side of the machine.
| |
| Illustration 3 | g01974234 |
This additional message identifies the location of the fast fill connector for the engine coolant.
Extended Life Coolant (2). This message is located next to the cooling system pressure cap.
| |
| Illustration 4 | g01314339 |
The cooling system is filled with ELC (Extended Life Coolant) from the factory.
Hydraulic Oil Fast Fill (3). This message is located beside the hydraulic tank on the right side of the machine.
| |
| Illustration 5 | g01429855 |
This additional message identifies the location of the fast fill connector for the hydraulic oil.
Alternate Exit (4)
This message is located on the outside of the right side window and the front window.
| |
| Illustration 6 | g00915912 |
Alternate Exit (4)
This message is located on the right side window and the front window.
| |
| Illustration 7 | g01002993 |
Transmission Oil Fast Fill (5). This message is located in the articulation area above the transmission oil sight gauge on the right side of the machine.
| |
| Illustration 8 | g01974236 |
This additional message identifies the location of the fast fill connector for the transmission oil.
Retarding Guidelines (6). This message is located inside the cab.
| |
| Illustration 9 | g01978754 |
For more information on retarding, refer to Operation and Maintenance Manual, "Retarding".
Fire Suppression System (Foam) (If Equipped) (7). This message is located on the left side of the radiator guard and in the operator station.
| |
| Illustration 10 | g01547033 |
For more information on the foam fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Foam)".
Engine Oil (If Equipped) (8). This message is located next to the engine oil fill tube on the right side of the machine.
| |
| Illustration 11 | g02448560 |
Cat DEO-ULS oils and oils that satisfy the "API CJ-4"and/or "ACEA E9" requirements are required for engines that are equipped with a Flow Through Diesel Particulate Filter.
Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for more information about the oil.
Fire Suppression System (Foam) (If Equipped) (9). This message is located on the left side of the radiator guard and in the operator station.
| |
| Illustration 12 | g01959382 |
For more information on the foam fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Foam)".
Fire Suppression System (Dry Powder) (If Equipped) (10). This message is located on the left side of the radiator guard and in the operator station.
| |
| Illustration 13 | g01431885 |
For more information on the dry powder fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Dry Powder)".
Diesel Fuel Requirements (If Equipped) (11). This additional message is located next to the fuel tank filler cap.
| |
| Illustration 14 | g02399176 |
Note: This information is pertinent to the United States of America (USA) and Canada.
If applicable, consult the federal, state, local, and other governing authorities for guidance concerning the fuel requirements in your area.
For more information about diesel fuels, refer to Special Publication, SEBU6250, "AVSpare Machine Fluids Recommendations".
Diesel Fuel Requirements (If Equipped) (11). This additional message is located next to the fuel tank filler cap.
| |
| Illustration 15 | g02052934 |
Use Ultralow Sulfur Diesel (ULSD) fuel.
The United States (U.S.) Environmental Protection Agency (EPA) defines Ultra-Low Sulfur Diesel (ULSD - S15) as a U.S. diesel fuel with a sulfur content not to exceed 15 parts per million (ppm(mg/kg)) or 0.0015 percent by weight. Engines equipped with exhaust aftertreatment systems are designed to run on ULSD only. Use of LSD or fuels higher than 15 ppm (mg/kg) sulfur in these engines will reduce engine efficiency and engine durability. Damage to the emissions control systems will occur. Failures that result from the use of fuels are not AVSpare factory defects. Therefore the cost of repairs would not be covered by a AVSpare warranty.
In Europe, ultra low sulfur diesel fuel will have a maximum of 0.0010 percent (10 ppm(mg/kg)) sulfur and is typically referred to as “sulfur-free”. This sulfur level is defined in European Standard "EN 590:2004".
Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for more information about the fuel.
Also, refer to Special Publication, SEBU6250, "AVSpare Machine Fluids Recommendations" for more information about diesel fuels.
24 V Electrical System (12)
This message is located next to the jump-start receptacle.
This machine is equipped with a 24 V electrical system.
| |
| Illustration 16 | g01126478 |