D11R Track-Type Tractor C32 Engine Retrofit Supplement Engine Mounts and Equalizer Bar - Inspect Caterpillar


Engine Mounts and Equalizer Bar - Inspect
`
D11R Track-Type Tractor C32 Engine Retrofit Supplement [SEBU9433]
BASIC ENGINE
MOUNTING GP-ENGINE
D11R Track-Type Tractor C32 Engine Retrofit Supplement Engine Mounts and Equalizer Bar - Inspect
D11R Track-Type Tractor C32 Engine Retrofit Supplement Engine Mounts and Crankshaft Vibration Damper - Inspect
1.1. Engine Mounts
2.1. Equalizer Bar End Pins
3.1. Equalizer Bar Center Pin
4.1. Equalizer Bar Pads

Engine Mounts

AVSpare recommends checking the engine mounts for deterioration. This will prevent excessive engine vibration that is caused from improper mounting.

Equalizer Bar End Pins

------ WARNING! ------

Personal injury or death can occur from not following the proper procedure or the recommended tooling.

To prevent the possibility of injury or death, follow the established procedure using the recommended tooling.



NOTICE

The machine must be parked on a level surface to perform this procedure.


------ WARNING! ------

Personal injury or death can occur from not following the proper procedure or the recommended tooling.

To prevent the possibility of injury or death, follow the established procedure using the recommended tooling.



NOTICE

The machine must be parked on a level surface to perform this procedure.


Note: All the weight of the machine must be removed from the equalizer bar. Equalizer bar must have free movement in order to be measured.

To check the equalizer bar end pin for movement and unusual wear, perform the following steps.



    Illustration 1g01108793

  1. Clean the areas that are around the end pin with a high pressure wash. Inspect the condition of the seal.

  2. Check the area for oil leakage and a neutral seal position.

  3. Check the oil in both end pin joints.


    Illustration 2g01108795

  4. Position a dial indicator on the bracket for the pin on the roller frame. Set the dial indicator probe on top of the equalizer bar. Set the dial indicator to zero.


    Illustration 3g01108798

  5. Put a suitable floor jack in position under the end of the equalizer bar.

  6. Jack up the equalizer bar and take a reading on the dial indicator in order to determine the amount of wear.

    Note: Schedule the end pin joint for repair if the reading on the dial indicator exceeds 1.50 mm (.059 inch).

  7. Repeat the inspection and the measurement procedure for the other end of the equalizer bar and end pin.

Consult your AVSpare dealer for an inspection and for repair instructions.

Equalizer Bar Center Pin

------ WARNING! ------

Personal injury or death can occur from not following the proper procedure or the recommended tooling.

To prevent the possibility of injury or death, follow the established procedure using the recommended tooling.



NOTICE

The machine must be parked on a level surface to perform this procedure.


------ WARNING! ------

Personal injury or death can occur from not following the proper procedure or the recommended tooling.

To prevent the possibility of injury or death, follow the established procedure using the recommended tooling.



NOTICE

The machine must be parked on a level surface to perform this procedure.


Note: All the weight of the machine must be removed from the equalizer bar. Equalizer bar must have free movement in order to be measured.

To check the equalizer bar center pin for looseness and for unusual wear, perform the following steps.



Illustration 4g01108801

  1. Clean the areas that are around the center pin and equalizer bar.


    Illustration 5g01108803

  2. Put a suitable floor jack in position under the main frame, as shown.


    Illustration 6g01108804

  3. Position a dial indicator on the equalizer bar and place the probe of the dial indicator under the center of the frame for the pin. Set the dial indicator to zero.

  4. Jack up the front of the machine until the weight of the roller frames are supported by the equalizer bar.

  5. Take a reading of the dial indicator in order to determine the amount of wear on the pin and bearing.

Note: Schedule the center pin joint for repair if movement exceeds 2.54 mm (.100 inch).

Consult your AVSpare dealer for an inspection and for repair instructions.

Equalizer Bar Pads



Illustration 7g01108806

The equalizer bar pads are under the front guard, which is underneath the machine. Inspect the equalizer bar pads for cracked rubber and for missing portions of rubber. Consult your AVSpare dealer for replacement parts and for replacement instructions.

Information System:

992K Wheel Loader Electrohydraulic System MID 082 - CID 1571 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 0967 - FMI 14
992K Wheel Loader Electrohydraulic System MID 082 - CID 0967 - FMI 09
992K Wheel Loader Electrohydraulic System MID 082 - CID 0800 - FMI 14
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0290 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0262 - FMI 04
854G and 854K Wheel Dozers and 992G, 992K and 994F Wheel Loaders VIMSTM MID 049 - CID 0262 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 0351 - FMI 03
992K Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 04
992K Wheel Loader Electrohydraulic System MID 082 - CID 0350 - FMI 03
D7E Track-Type Tractor Winch Oil and Breather - Change/Clean - If Equipped
TS180, TS185, TS220 and TS225 Towed Scrapers Maintenance Interval Schedule
PL61 Pipelayer Declaration of Conformity
D11T Track-Type Tractor Automatic Lubrication System General Information
D7R Series II Track-Type Tractor Specifications
988G Wheel Loader Power Train MID 081 - CID 0603 - FMI 03
C7.1 Industrial Engine Starting with Jump Start Cables - Do Not Use This Procedure in Hazardous Locations that have Explosive Atmospheres
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 00
Documenting the Date Codes of the Bearings for 3500 and G3600 Engines{1202, 1225}
992K Wheel Loader Electrohydraulic System MID 082 - CID 2416 - FMI 01
2013/01/14 A New Idler Pulley Assembly Is Now Used For the D8T, 583T, and 587T {1405, 1802, 7320}
D7R Series II Track-Type Tractor Safety Messages
854K Wheel Dozer and 992K Wheel Loader Power Train MID 081 - CID 0262 - FMI 03