928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) Rated Load Caterpillar


Rated Load
`
928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) [GEBU0008]
WORK TOOLS
FORK GP
928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) Pallet Fork - Inspect
928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) Rated Load
2.1. Definitions
3.2. Industry Standards
4.2. Load Center
5.2. Static Tipping Loads (Forks Level)
6.1. Load Rating of Tine

------ WARNING! ------

Failure to comply to the rated load can cause possible personal injury or property damage. Review the rated load of a particular work tool before performing any operation. Make adjustments to the rated load as necessary for non-standard configurations.

----------------------

------ WARNING! ------

To prevent injury, do not exceed the rated load capacity that is stamped in the side of each fork tine.

----------------------

------ WARNING! ------

To prevent injury, do not exceed the rated load capacity of the machine. If the machine is not on level ground, load capacities will vary.

----------------------

Note: Rated loads should be used as a guideline. Work tools, uneven ground conditions, soft ground conditions, or poor ground conditions have effects on rated loads. The operator is responsible for being aware of these effects.

Note: Contact your AVSpare dealer if the load chart for a specific combination is not available.

Definitions

Industry Standards

  • Society of Automotive Engineers (SAE) J1197: 2002 Rated Operating Load for Loaders Equipped with Log or Material Forks without Vertical Mast - specifies that the rated operating load is the minimum of either 50% of the full turn static tipping load (FTSTL) OR the minimum hydraulic capacity of the machine.

  • European Committee for Standardization (CEN) EN 474-3: 2006 Earth-moving machinery - Safety - Part 3: Requirements for loaders - specifies that the rated operating load on rough terrain is the minimum of either 60% of the full turn static tipping load (FTSTL) OR the minimum hydraulic capacity of the machine.

  • European Committee for Standardization (CEN) EN 474-3 - specifies that the rated operating load on firm and level ground is the minimum of either 80% of the full turn static tipping load (FTSTL) OR the minimum hydraulic capacity of the machine.

Load Center

The load center is defined as the distance from the tine shank (vertical portion of the tine that a load rests against) to the center of the object being lifted.

Static Tipping Loads (Forks Level)

Static tipping loads are based on the following assumptions: machines are non-moving, on firm and level ground, forks level, and tipping loads are measured at the moment when the rear tires just begin to lift off the ground. Static tipping loads are different for each machine configuration, pallet fork, and load center combination.

The straight static tipping load (SSTL) is a measure of the machine's stability in the non-articulated condition. SSTL for a machine equipped with pallet forks is calculated with the pallet forks level and occurs when the lift arms are level.

The full turn static tipping load (FTSTL) is a measure of the machine's stability in the fully articulated condition. FTSTL for a machine equipped with pallet forks is calculated with the pallet forks level and occurs when the lift arms are level.

Load Rating of Tine

------ WARNING! ------

To prevent injury, do not exceed the rated load capacity that is stamped in the side of each fork tine.

----------------------

Table 1
Tine As    
Machine Ar     Fork Tine As Part Number     Load Center of Fork Tine     Load Capacity of Fork Tines (per pair of fork tines)    
924Gz - 938H     168-4526    
914.40 mm (36 inch)    

7365 kg (16204 lb)    

Note: The capacity that is stamped on each tine is specific to the tine. The capacity does not represent a combined rating for both tines. The capacity does not represent a combined rating for the fork carriage.

Information System:

2011/02/18 The Check Valve Group Has Been Improved on Certain Wheel Tractor-Scrapers {5057, 5067}
928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) Work Tool Installation and Removal
928HZ Wheel Loader - 344-7157 Pallet Fork (Custom Product) Pallet Fork - Inspect
D7E Track-Type Tractor Power Train Systems Front Idler
D11T Track-Type Tractor Automatic Lubrication Grease Tank - Fill - If Equipped
Diagnostic Process for Fuel Rail Pressure Sensor{1718}
2011/05/31 Correction to Operation and Maintenance Manual , "Braking System - Test" {4250, 4251, 4267}
D7E Track-Type Tractor Power Train Systems Steering Hesitates
D7E Track-Type Tractor Power Train Systems Backup Alarm Does Not Function
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Fuel Tank Underfills (Fast Fill Fuel)
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Fueling Nozzle Shuts Off Prematurely (Fast Fill Fuel)
D11T Track-Type Tractor Lifting and Tying Down the Machine
Rework Procedure To Relocate the Cab Pressurizer{7311, 7342}
2009/08/31 Hydraulic Oil Lines Groups for the Power Train Have Been Updated on Certain Wheel Tractor-Scrapers {3016, 3177}
2009/09/07 New Shims are Available for Certain 630 Wheel Tractor-Scrapers {1152, 1153, 1154}
2009/08/31 New CapSure Tip Assemblies Are Now Available for J800 Adapters {6805}
D7E Track-Type Tractor Engine Starting with Auxiliary Start Receptacle - If Equipped
621G, 623G and 627G Wheel Tractor-Scrapers Machine Systems System Pressure - Release
Procedure to Rework the Latches for the Rear Access Egress System RAES on the 993K Wheel Loaders{0679, 7011, 7256, 7273, 7277}
993K Wheel Loader Assembly Procedure{7000, 7960}
Installation Of the Autolube System For the D11T{7540}
C9.3 Tier 4 Final Engines Fuel System - Prime
D7E Track-Type Tractor Machine Systems Piston Pump (Steering) - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Compression Brake Lash - Adjust