AD55B Underground Articulated Truck Additional Messages Caterpillar


Additional Messages
`

There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Become familiarized with all messages.

Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.

Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any AVSpare dealer can provide new messages.




Illustration 1g01950902



Illustration 2g02399237



Illustration 3g03718736

Retarding Guidelines (1) . This message is located inside the cab.




Illustration 4g01950903

For more information on retarding, refer to Operation and Maintenance Manual, "Retarding".

Engine Coolant Fast Fill (2) . This message is located at the front of the radiator on the right side of the machine.




Illustration 5g01419256

This message identifies the location of the fast fill connector for the engine coolant.

Alternate Exit (3)

This message is located on the outside of the right side window and the front window.




Illustration 6g01419258

If the primary exit is blocked, pull on the locking strip tab to remove the locking strip. Exert inwards pressure on the window, until the window separates from the operator station frame. Exit the machine through the window.

Alternate Exit (3)

This message is located on the right side window and the front window.




Illustration 7g01002993

If the primary exit is blocked, exert outward pressure on the window until the window separates from the operator station frame. Exit the machine through the window.

Extended Life Coolant (4) . This message is located next to the cooling system pressure cap.




Illustration 8g01314339

The cooling system is filled with ELC (Extended Life Coolant) from the factory.

Engine Oil Fast Fill (5) . This message is located beside the engine oil dipstick on the right side of the machine.




Illustration 9g01419259

This message identifies the location of the fast fill connector for the engine oil.

Transmission Oil Fast Fill (6) . This message is located in the articulation area on the right side of the machine.




Illustration 10g01419260

This message identifies the location of the fast fill connector for the transmission oil.

Hydraulic Oil Fast Fill (7) . This message is located beside the hydraulic tank on the right side of the machine.




Illustration 11g01419603

This message identifies the location of the fast fill connector for the hydraulic oil.

Fire Suppression System (Dry Powder) (If Equipped) (8) . This message is located on the left side of the radiator guard and in the operator station.




Illustration 12g01431885

For more information on the dry powder fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Dry Powder)".

Fire Suppression System (Foam) (If Equipped) (9) . This message is located on the left side of the radiator guard and in the operator station.




Illustration 13g01547033

For more information on the foam fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Foam)".

Fire Suppression System (Foam) (If Equipped) (10) . This message is located on the left side of the radiator guard.




Illustration 14g01434323

For more information on the foam fire suppression system, refer to Operation and Maintenance Manual, "Fire Suppression System (Foam)".

24 V Electrical System (11) . This additional message is located next to the jump-start receptacle.




Illustration 15g01126478

This machine is equipped with a 24 V electrical system.

Diesel Fuel Requirements (12) . This additional message is located next to the fuel tank filler cap.




Illustration 16g02399176

Note: This information is pertinent to the United States of America (USA) and Canada.

If applicable, consult the federal, state, local, and other governing authorities for guidance concerning the fuel requirements in your area.

For more information about diesel fuels, refer to Special Publication, SEBU6250, "AVSpare Machine Fluids Recommendations".

Information System:

AD55B Underground Articulated Truck Safety Messages
966H Wheel Loader and 972H Wheel Loader Braking and Hydraulic Fan System Pressure Switch (Parking Brake Oil)
D6T Track-Type Tractor Systems Hydraulic Fan Speed (On Demand) - Test and Adjust
Camshaft Lobe Hits Fuel Transfer Pump.{1210, 1256}
953D, 963D and 973D Track-Type Loaders Ripper Does Not Function
953D, 963D and 973D Track-Type Loaders Implement Cycle Time Is Fast
C12 Marine Engines and C12 Power Package Maintenance Recommendations
973D Track-Type Loader Declaration of Conformity
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
953D, 963D and 973D Track-Type Loaders Hydraulic System Oil Temperature Is High
2009/09/07 Protective Covers For the Joint On the Equalizer Bar Are Now Used {7206}
C9.3 Tier 4 Final Engines Lubrication System
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 04
C3.4B Engines for Caterpillar Built Machines Alternator - Test
953D Track-Type Loader Machine Systems Window Wiper and Wiper Motor
C9.3 Engine and D7E Track-Type Tractors Power Train Oil Cooler - Remove and Install
Piston Seizures on C18 Engines{1225, 1331}
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Contains Air
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Level Is Low
D7E Track-Type Tractor Hydraulic, HVAC, and Electrical Systems Hydraulic System Oil Temperature Is High
953D, 963D and 973D Track-Type Loaders Steering Does Not Function
953D, 963D and 973D Track-Type Loaders Steering Does Not Function in One Direction
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Power Train MID 081 - CID 0070 - FMI 03
973D Track-Type Loader Machine Systems Window Wiper and Wiper Motor