Cooling System Coolant Level - Check
`
C4.4 Industrial Engine
[SEBU8606]
C4.4 Industrial Engine
Engine Electronics
C4.4 Industrial Engine
Cooling System Coolant Extender (ELC) - Add
COOLING SYSTEM
RADIATOR GP
3508, 3512, and 3516 Generator Sets
Cooling System Coolant Sample (Level 1) - Obtain
C4.4 Industrial Engine
Cooling System Coolant Level - Check
C4.4 Industrial Engine
Cooling System Coolant Extender (ELC) - Add
C4.4 Industrial Engine
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
C4.4 Industrial Engine
Cooling System Coolant (DEAC) - Change
C4.4 Industrial Engine
Cooling System Coolant (ELC) - Change
C4.4 Industrial Engine
Radiator - Clean
Check the coolant level when the engine is stopped and cool.
Show/hide table
| |
| Illustration 1 | g00285520 |
|
Cooling system filler cap | |
Show/hide table
 |
|
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure. |
Show/hide table
| NOTICE |
|---|
|
When any servicing or repair of the engine cooling system is performed, the procedure must be performed with the engine on level ground. This procedure will allow you to check accurately the coolant level. This procedure will also help in avoiding the risk of introducing an air lock into the coolant system. |
- Remove the cooling system filler cap slowly in order to relieve pressure.
- Maintain the coolant level at the maximum mark that is correct for your application. If the engine is equipped with a sight glass, maintain the coolant level to the correct level in the sight glass.
Show/hide table
Illustration 2 g02590196 Typical filler cap gaskets - Clean the cooling system filler cap and check the condition of the filler cap gaskets. Replace the cooling system filler cap if the filler cap gaskets are damaged. Reinstall the cooling system filler cap.
- Inspect the cooling system for leaks.
Information System:
C4.4 Industrial Engine
Valve Depth - Inspect
C4.4 Industrial Engine
Compression - Test
C7.1 Industrial Engine
Fuel Injection Timing - Check
C4.4 Industrial Engine
Air in Fuel - Test
3500 Engines
Air Lines
3500 Engines
Air Inlet and Exhaust Lines
3500 Engines
Turbocharger
D6T Track-Type Tractor Systems
Accumulator (Pilot) - Test and Charge
2009/05/04
A Tilt Regeneration Kit Is Now Available for the 988G and 988H Machines {1408, 5057, 5104, 512R}
D6T Track-Type Tractor Systems
Piston Pump (Implement) - Test and Adjust
D6T Track-Type Tractor Hydraulic System
Operational Checks
C9.3 Engines for Caterpillar Built Machines
Fuel Injection Pump - Test
C7.1 Industrial Engine
Engine Oil Cooler - Inspect
C7.1 Industrial Engine
Connecting Rod - Inspect
C7.1 Industrial Engine
Cylinder Head - Inspect
C4.4 Industrial Engine
Flywheel - Inspect
C7.1 Engines for Caterpillar Built Machines
Vibration Damper - Check
C4.4 Industrial Engine
Cooling System - Test
C7.1 Industrial Engine
Engine Oil Pump - Inspect
C7.1 Industrial Engine
Finding Top Center Position for No. 1 Piston
C7.1 Industrial Engine
Basic Engine
C7.1 Industrial Engine
Cooling System
C7.1 Engines for Caterpillar Built Machines
Electrical System
C7.1 Industrial Engine
Fuel Injection