(30)Lubricate fan drive bearing
(31)Lubricate track adjusting screws
(32)Check steering clutch brakes (Lever Steer Machines)
FREE TRAVEL must be 3 inches (76,2 mm)
To Adjust
- 1. REMOVE cover
- 2. TIGHTEN nut
- 3. LOOSEN locknut
- 4. TIGHTEN screw
- 5. LOOSEN screw 1 turn
- 6. TIGHTEN locknut
- 7. LOOSEN nut 3 turns
- 8. INSTALL cover
- 9. CHECK adjustment
REPEAT PROCEDURE for opposite steering clutch brake
(Pedal Steer Machines)
FREE TRAVEL must be 3 inches (76,2 mm)
- 1. REMOVE cover
- 2. TIGHTEN nut until snug
- 3. LOOSEN nut 2-1/2 turns
- 4. INSTALL cover
- 5. CHECK adjustment
REPEAT PROCEDURE for opposite steering clutch brake
(33)Clean diesel fuel tank filler cap
- 1. REMOVE cap
- 2. DISASSEMBLE
- 3. WASH cap and elements in kerosene or clean diesel fuel
- 4. LIGHTLY coat with lubricating oil
(34)Clean fuel tank filler strainer
- 1. REMOVE lock ring and strainer
- 2. CLEAN in kerosene or clean diesel fuel
- 3. INSTALL strainer and lock ring
No smoking around flammable liquids
(35)Change transmission oil filter element
- 1. REMOVE side covers
- 2. REMOVE cover and element
- 3. SEPARATE element from cover INSPECT seals
- 4. INSTALL new element TIGHTEN to 10 ± 2 lb. ft. (1,4 ± 3 mkg)
- 5. INSTALL element and cover START engine
- 6. CHECK oil level
- 7. ADD oil as required
(36)Check fan and generator belts
- 1. CHECK for wear
- 2. CHECK adjustment
Correct adjustment-7/8" (22 mm) (Initial installation with new belts-3/4" [19 mm])
To Adjust Belts
- 1. LOOSEN bolts
- 2. MOVE generator
- 3. TIGHTEN bolts
- 4. CHECK adjustment
(37)*Change diesel engine crankcase oil and filter element
- 1. REMOVE cover REMOVE drain plug
- 2. Drain crankcase
- 3. INSTALL drain plug INSTALL cover
- 4. REMOVE side cover
- 5. REMOVE drain plug DRAIN housing
- 6. INSTALL drain plug
- 7. REMOVE housing and old element
- 8. CHECK seal
- 9. INSTALL new element and housing
- 10. Fill crankcase
- 11. To level on gauge
- 12. START engine
- 13. CHECK oil level
- 14. ADD oil as required To FULL mark on ENGINE RUNNING side of gauge
*See PERIODIC SERVICE INDEX for reduced intervals.
(38)Wash diesel engine crankcase breather
- 1. REMOVE breather
- 2. WASH in clean kerosene or diesel fuel
- 3. CHECK seal
- 4. INSTALL breather
(39)Wash transmission breather
- 1. REMOVE breather
- 2. WASH in clean kerosene or diesel fuel
- 3. Oil lightly
- 4. INSTALL
(40)Wash bevel gear compartment breather
- 1. REMOVE breather
- 2. Wash in clean kerosene or diesel fuel
- 3. Oil lightly
- 4. INSTALL
(41)Change hydraulic control system oil filter element
- 1. LOWER raised equipment
- 2. REMOVE cover
- 3. REMOVE element
- 4. INSPECT seal
- 5. INSTALL new element
- 6. TIGHTEN to 43 ± 4 lb. ft. (5,9 ± 0,6 mkg)
- 7. OPEN bleed valve
- 8. START engine
- 9. CLOSE bleed valve when oil flows without air bubbles
- 10. CHECK oil level
- 11. ADD oil as necessary
(42)*Change bevel gear and steering clutch oil filter element
- 1. REMOVE cover
- 2. REMOVE element
- 3. INSPECT seal
- 4. INSTALL new element
- 5. INSTALL cover
- 6. START engine
- 7. CHECK oil level
- 8. ADD oil as required
(43)*Wash bevel gear and steering clutch compartment oil screen
- 1. REMOVE cover
- 2. REMOVE screen
*Pedal steering machines only
- 3. WASH in kerosene or clean diesel fuel
- 4. INSTALL screen
- 5. INSPECT seals
- 6. INSTALL cover